Canon imageRUNNER ADVANCE C3325 Series Service Manual page 781

SORTER>ADJUST
SDL-ALM Set sddl stack full alarm mode: Fin-U1
Lv.1 Details To set ON/OFF of saddle stack full alarm.
Set to 1 when disabling the stack full alarm for saddle stitching.
When 1 is set, the saddle stack capacity increase mode (SDL-SWCH)
is disabled.
Use case When disabling the stack full alarm for saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 1 is set, the saddle delivery sensor stationary jam may occur
because the paper stack on the saddle delivery tray block up the
saddle delivery port.
Display/adj/set range 0 to 1
0: OFF (Alarm detection), 1: ON (Non Alarm detection)
Default value 0
Related service mode SORTER> ADJUST> SDL-SWCH
INSTP-F1 Adj front 1-stapling position: Fin-G1
Lv.1 Details To adjust the front 1-staple position.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: Toward rear
-: Toward front
Use case When the staple position in front/rear direction is displaced in the front
1-stapling mode
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
INSTP-R1 Adj rear 1-stapling position: Fin-G1
Lv.1 Details To adjust the rear 1-staple position.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: Toward rear
-: Toward front
Use case When the staple position in front/rear direction is displaced in the rear
1-stapling mode
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
THN-STCL [Not used]
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER>ADJUST
FR-ST-PS Adjust staple free pressure: Fin-G1
Lv.1 Details To adjust the staple pressure in the staple free stapling mode.
As the value is changed by 1, the staple pressure changes by 1 mNm.
+: Increased
-: Decreased
Use case Upon user's request
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Caution As the value is increased, the life of the Stapler is shortened.
Display/adj/set range -15 to 15
Unit 1 mNm
Default value 0
FR-STP-X Adj stpl free stpl pstn (Fd way): Fin-G1
Lv.1 Details To adjust the staple position for paper feed direction in the staple free
stapling mode.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: Leading edge direction
-: Trailing edge direction
Use case When the staple position in paper feed direction is displaced in the
staple free stapling mode
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -15 to 15
Unit 0.1 mm
Default value 0
Supplement/memo Change the paper shift amount in the paper feed direction. The staple
free stapler position is not changed.
FR-STP-Y Adj stpl free stpl pstn (F/R way):Fin-G1
Lv.1 Details To adjust the staple position for front/rear direction in the staple free
stapling mode.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: Toward rear
-: Toward front
Use case When the staple position in front/rear direction is displaced in the
staple free stapling mode
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -30 to 30
Unit 0.1 mm
Default value 0
Supplement/memo Change the paper shift amount in the front/rear direction. The staple
free stapler position is not changed.
8-230
8-230