Fixing Disengagement Timeout Error; Bk Drum_Itb Motor Error - Canon imageRUNNER ADVANCE C3325 Series Service Manual

Error■ Detail■
Location Item
code Code
E009 0001 05 Title Fixing■disengagement■timeout■error
Detection■ The■Fixing■Pressure■Release■Sensor■did■not■detect■OFF■status■
description within■10■sec■after■the■start■of■fixing■disengagement■operation.
Remedy [Related■parts]
•■ Harnesses■from■the■DC■Controller■PCB■to■the■Fixing■Pressure■
Release■Sensor
1.■DC■Controller■PCB■(UN04/J122)■to■Relay■Connector■(11P)■(Unit■
of■replacement:■CABLE,■FEED)
2.■Relay■Connector■(11P)■to■Fixing■Pressure■Release■Sensor■
(PS13)■(Unit■of■replacement:■PAPER■DELIVERY■DRIVE■
ASSEMBLY)
•■ Harnesses■from■the■DC■Controller■PCB■to■the■Fixing■Motor
1.■DC■Controller■PCB■(UN04/J122)■to■Relay■Connector■(8P)■(Unit■
of■replacement:■CABLE,■FEED)
2.■Relay■Connector■(8P)■to■Fixing■Motor■(M09)■(Unit■of■
replacement:■FIXING■DRIVE■MOTOR■ASSEMBLY)
•■ Fixing■Unit■(Unit■of■replacement:■FIXING■ASSEMBLY)
•■ DC■Controller■PCB■(UN04)■(Unit■of■replacement:■DC■
CONTROLLER■PCB■ASSEMBLY)
•■ Fixing■Pressure■Release■Sensor■(PS13)
•■ Fixing■Drive■Unit■(Unit■of■replacement:■FIXING■DRIVE■
ASSEMBLY)
[Remedy]■Check/replace■the■related■harness/cable,■connector■
and■parts.
[Reference]■Before■replacing■the■DC■Controller■PCB,■back■up■the■
service■mode■data■(approx.■2■min)■and■restore■the■backup■data■
after■the■replacement■so■the■data■may■be■able■to■be■protected.
•■ Backup:■COPIER■(LEVEL2)>■FUNCTION>■SYSTEM>■
DSRAMBUP
•■ Restoration:■COPIER■(LEVEL2)>■FUNCTION>■SYSTEM>■
DSRAMRES
7
Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Description
7 Error•Jam•Alarm■>■Error■Code■>■Error■Code■Details
Error■ Detail■
Location Item
code Code
E010 0001 05 Title Bk■Drum_ITB■Motor■error
Detection■ It■did■not■become■the■specified■speed■for■0.5■consecutive■sec■
description although■0.8■sec■have■passed■from■the■startup■of■the■Bk■Drum_
ITB■Motor■in■the■Main■Drive■Unit.
Remedy [Related■parts]
•■ Harness■between■the■Bk■Drum_ITB■Motor■(M02/J1054)■and■the■
DC■Controller■PCB■(UN04/J129)■(Unit■of■replacement:■CABLE,■
MAIN■DRIVE)
•■ Main■Drive■Unit■(Unit■of■replacement:■MAIN■DRIVE■
ASSEMBLY)
•■ Bk■Drum_ITB■Motor■(M02)
•■ DC■Controller■PCB■(UN04)■(Unit■of■replacement:■DC■
CONTROLLER■PCB■ASSEMBLY)
•■ Low■Voltage■Power■Supply■PCB■(UN01)■(Unit■of■replacement:■
POWER■SUPPLY■ASSEMBLY)
[Remedy]■Perform■the■following■in■the■order■while■checking■
whether■the■error■is■cleared.
1.■Check■whether■the■gears■of■the■Main■Drive■Unit■can■be■rotated■
by■hand.
a.■If■they■cannot■be■rotated,■replace■the■Main■Drive■Unit.
b.■If■they■can■be■rotated,■check■the■harness■between■the■Bk■
Drum_ITB■Motor■and■the■DC■Controller■PCB.
2.■Measure■the■both■ends■of■the■fuse■in■the■Low■Voltage■Power■
Supply■PCB■using■a■tester.
a.■If■the■measurement■value■is■less■than■1■ohm■(conduction■
state),
1.■Replace■the■Bk■Drum_ITB■Motor.
2.■Replace■the■DC■Controller■PCB.
b.■If■the■measurement■value■is■1■ohm■or■higher■(non■conduction■
state),■replace■the■Low■Voltage■Power■Supply■PCB.
[Reference]■Before■replacing■the■DC■Controller■PCB,■back■up■the■
service■mode■data■(approx.■2■min)■and■restore■the■backup■data■
after■the■replacement■so■the■data■may■be■able■to■be■protected.
•■ Backup:■COPIER■(LEVEL2)>■FUNCTION>■SYSTEM>■
DSRAMBUP
•■ Restoration:■COPIER■(LEVEL2)>■FUNCTION>■SYSTEM>■
DSRAMRES
7-13
Description
7-13