Canon imageRUNNER ADVANCE C3325 Series Service Manual page 660

COPIER>ADJUST>FEED-ADJ
LP-DUP1 Adj pre-rgst arch amount: plain, 2-sided
Lv.1 Details To adjust the arch amount before registration for paper belonging to a
group of plain papers fed in 2-sided mode.
As the value is changed by 1, the arch amount is changed by 0.1 mm.
+: Increase
-: Decrease
Use case When an image on the 2nd side of paper belonging to a group of plain
papers fed in 2-sided mode is skewed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
Supplement/memo Group of plain papers: Plain paper 1/2/3, colored paper, recycled
paper, pre-punched paper, tracing paper
LP-DUP2 Adj pre-rgst arch amount: heavy, 2-sided
Lv.1 Details To adjust the arch amount before registration for paper belonging to a
group of heavy papers fed in 2-sided mode.
As the value is changed by 1, the arch amount is changed by 0.1 mm.
+: Increase
-: Decrease
Use case When an image on the 2nd side of paper belonging to a group of
heavy papers fed in 2-sided mode is skewed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
Supplement/memo Group of heavy papers: Heavy paper 1/2/3/4, coated paper 1/2/3,
transparency, label, bond paper, envelope, postcard
REG-SPD Adjustment of Registration Motor speed
Lv.1 Details To adjust the speed of the Registration Motor.
As the value is changed by 1, the speed is changed by 0.2%.
+: Increase
-: Decrease
As the value is reduced, blur image in the area of 60 to 70 mm from
the trailing edge is alleviated.
Use case When blur image occurs in the area of 60 to 70 mm from the trailing
edge
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -5 to 5
Unit 0.2 %
Default value 0
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER>ADJUST>FEED-ADJ
EXT-SPD Setting of delivery speed at 1/1 speed
Lv.2 Details To set the delivery speed of papers (thin paper 1, plain paper 1/2/3,
colored paper 1, recycled paper 1/2/3, pre-punched paper 1 and
tracing paper) which are fed at 1/1 speed in the case of delivering to
the First/Second Delivery Tray.
Set 2 if misalignment occurs with the papers when delivering to the
First Delivery Tray. Speed of the Fixing Motor is reduced so that
papers are stacked on the First Delivery Tray more gently.
Set 1 if trailing edges of papers with 297 mm (A4R) or less in length
get caught on the delivery outlet when delivering to the Second
Delivery Tray. Speed of the Second Delivery Motor is increased so that
trailing edge of paper can pass through the delivery outlet.
Set 3 if both of the above symptoms occur.
Use case - When misalignment occurs at delivery to the First Delivery Tray
- When trailing edge of paper get caught on the delivery outlet at
delivery to the Second Delivery Tray
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 2 or 3 is set, FCOT becomes longer.
Display/adj/set range 0 to 3
0: Normal, 1: Increase the speed at delivery to the Second Delivery
Tray, 2: Reduce the speed at delivery to the First Delivery Tray, 3:
Reduce the speed at delivery to the First Delivery Tray and increase
the speed at delivery to the Second Delivery Tray
Default value 0
LP-FEED3 Adj pre-rgst arch amount: thin, Casstt
Lv.1 Details To adjust the arch amount before registration for thin paper fed from a
cassette.
As the value is changed by 1, the arch amount is changed by 0.1 mm.
+: Increase
-: Decrease
Use case When an image on the 1st side of thin paper fed from a cassette is
skewed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
8-109
8-109