Canon imageRUNNER ADVANCE C3325 Series Service Manual page 684

COPIER > OPTION > FNC-SW
ORG-LTR Special paper size set in DADF mode: LTR
Lv.2 Details To set the size of special paper (LTR configuration) that cannot be
recognized in DADF stream reading mode.
Use case - Upon user's request
- When picking up special paper size original from DADF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: LETTER, 1: EXECUTIVE, 2: Argentine LETTER, 3: Government
LETTER
Default value 0
ORG-LTRR Special paper size set in DADF mode:LTRR
Lv.2 Details To set the size of special paper (LTR-R configuration) that cannot be
recognized in DADF stream reading mode.
Use case - Upon user's request
- When picking up special paper size original from DADF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: LETTER-R, 1: OFICIO-R, 2: Ecuador OFICIO-R
Default value 0
ORG-LDR Special paper size set in DADF mode: LDR
Lv.2 Details To set the size of special paper (LDR configuration) that cannot be
recognized in DADF stream reading mode.
Use case - Upon user's request
- When picking up special paper size original from DADF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: LEDGER-R, 1: Argentine LETTER
Default value 0
INTROT-2 Set auto adj exe interval: last rotation
Lv.1 Details To set the interval (the number of sheets) to execute automatic
adjustment at last rotation.
As the value is changed by 1, the interval (the number of sheets) is
changed by 1 sheet.
Use case When matching the use environment of the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Increasing the number of sheets (widening the interval) causes higher
frequency of image failure.
Display/adj/set range 50 to 2000
Unit 1 sheet
Default value 1000
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
DMAX-SW ON/OFF of D-max control
Lv.2 Details To set ON/OFF of D-max control.
Use case - When the density variation is not within the requested range at
continuous output of a large volume of papers
- When keeping the productivity even though there are some density
variations
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
MODELSZ2 Ppr size dtct global support in bookmode
Lv.2 Details To set ON/OFF for global support of document size detection in
copyboard reading mode.
Use case Upon user's request (mixed media original with AB/Inch configuration)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The Document Size Sensor (Photo Sensor) is additionally required to
correctly detect the document size when the original consists of mixed
media (AB/Inch configuration).
Display/adj/set range 0 to 1
0: Detected with detection size according to location, 1: Detected with
AB/Inch mixed media.
Default value It differs according to the location.
SVMD-ENT Setting of entry method to service mode
Lv.2 Details To set the way to get in service mode to prevent information leak.
Use case As needed
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Factory default
1: [Settings/Registration] - Pressing [4] and [9] at the same time -
[Settings/Registration]
Default value 0
8-133
8-133