Delay - Korg pa 900 User Manual

Professional arranger
Hide thumbs Also See for pa 900:
Table of Contents

Advertisement

Effects
390

Delay

b: Speed Switch
This parameter controls how the rotation speed (slow and fast) is
switched via the modulation source.
When Mode = Toggle, the speed will switch between slow and
fast each time you press the pedal or move the joystick. Via
MIDI, the speed will switch each time the modulation amount
exceeds 64.
When Mode = Moment, the speed is usually slow. It becomes
fast only when you press the pedal or move the joystick. Via
MIDI, modulation values above 64 set the speed to Fast, and val-
ues below 64 set it to Slow.
c: Manual Speed Ctrl
If you wish to control the rotation speed manually, instead of
switching between Slow and Fast, select a modulation source in
the Manual Speed Ctrl parameter. If you don't want to use man-
ual control, set this to Off.
d: Horn Acceleration
e: Rotor Acceleration
On a real rotary speaker, the rotation speed accelerates or decel-
erates gradually after you switch the speed. The Horn and Rotor
Acceleration parameters set the transition times between fast
and slow speeds.
g: Mic Distance
g: Mic Spread
This is a simulation of stereo microphone settings.
Mic Spread
Microphone
Mic Distance
Rotary Speaker (Top View)
Rotary Speaker - Mic Placement
Microphone
Mic Distance
Delay
56: L/C/R Delay
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
L Delay Time
0...2730
[msec]
a
Level
0...50
C Delay Time
0...2730
[msec]
b
Level
0...50
R Delay Time
0...2730
[msec]
c
Level
0...50
Feedback
–100...+100
(C Delay)
d
Src
Off...Tempo
Amt
–100...+100
High Damp [%] 0...100
e
Low Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
f
Src
Off...Tempo
g Spread
0...50
Dry, 1:99...99:1,
Wet/Dry
Wet
h
Src
Off...Tempo
Amt
–100...+100
e: High Damp [%]
e: Low Damp [%]
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
FX Amt
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
FX Amt
Sets the delay time of TapL
Sets the output level of TapL
Sets the delay time of TapC
Sets the output level of TapC
Sets the delay time of TapR
Sets the output level of TapR
Sets the feedback amount of TapC
Selects the modulation source of the
TapC feedback amount
Sets the modulation amount of the
TapC feedback amount
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Sets the width of the stereo image of
the effect sound
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source

Advertisement

Table of Contents
loading

Table of Contents