Check The Signal Status; Set The Source Mux Settings - Lightware UBEX-PRO20-HDMI-F100 User Manual

 
     
4. Installation 4. Installation
4.8.4. Check the Signal Status
The Crosspoint menu in the LDC software displays all important information about the incoming, transmitting,
and outgoing HDMI signals. For more detailed information see the
The video crosspoint menu in the LDC software for TX-RX pair
Transmitter (UBEX TX) Side
Step 1. Check the HDMI signal status on the HDMI in 1 and 2 input ports - if the signal status indicator is green, the
signal is present; if it is grey, there is no incoming signal on the port.
Step 2. Check the HDMI signal status on the HDMI out 1 and 2 local output ports - if the signal status indicator is
green, the signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
Step 3. Check the video streams in the Stream 1 and 2 panels - if the signal status indicator is green, the signal is
present; if it is grey, there is no incoming signal on the port. Also check the enable status of the stream
on the stream settings panel.
Receiver (UBEX RX) Side
Step 1. Check the Stream switcher - the desired stream is switched to the HDMI output port.
Step 2. Check the HDMI signal status on the HDMI out 1 and 2 output ports - if the signal status indicator is green,
the signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
Transceiver (UBEX TRX) Side
Step 1. Check the HDMI signal status on the HDMI in 2 input port - if the signal status indicator is green, the signal
is present; if it is grey, there is no incoming signal on the port.
Step 2. Check the HDMI signal status on the HDMI out 1 output port - if the signal status indicator is green, the
signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
series – Extender Application Mode – User's Manual series – Extender Application Mode – User's Manual
Video Crosspoint Menu section.
Applied F-series endpoint firmware package: v2.0.0 | Applied R-series endpoint firmware package: v2.0.0 | LDC software: v2.5.9b3
SFP+ Links
Check the connection status of the SFP+ links:
▪ Green arrows mean connection is established and TCP/IP packages are
transmitted successfully.
▪ Amber arrows mean connection is established but error happened during
the transmission of the TCP/IP packages - check the SFP+ connection.
▪ Red arrows mean no connection is established between the endpoint
devices.
4.8.5. Set the Source MUX Settings

DEFINITION: The source multiplexer (Source MUX) makes available routing more different source signals
to the HDMI output ports. The setting is available only on the output ports of the receiver and transceiver
operation modes. The type of sources is different for the
outputs.
Click on the left side of the output port tile to access the MUX
settings. The available options are the following:
Receiver (UBEX RX) Side
For HDMI out 1
▪ Stream - The source signal is the stream received via the SFP+ links from the remote endpoint device;
HDMI in 1 - The source signal is the stream received via the local HDMI in 1 port.
▪
For HDMI out 2
▪ Stream - The source signal is the stream received via the SFP+ links from the remote endpoint device;
▪ HDMI in 2 - The source signal is the stream received via the local HDMI in 2 port.
▪ Copy - The receiver is able to copy the signal of the HDMI out 1 port. This is the COPY function.
Transceiver (UBEX TRX) Side
For HDMI out 2
▪ HDMI in 2 - The source signal is the stream received via the local HDMI in 2 port.
▪ Copy - The receiver is able to copy the signal of the HDMI out 1 port. This is the COPY function.
47 47