Siemens Sinamics G120 Series Parameter Manual page 305

p2170[0...2]
p2171[0...2]
p2172[0...2]
p2173[0...2]
p2174[0...2]
p2176[0...2]
p2177[0...2]
p2178[0...2]
p2181[0...2]
p2182[0...2]
p2183[0...2]
p2184[0...2]
p2185[0...2]
p2186[0...2]
p2187[0...2]
p2188[0...2]
p2189[0...2]
p2190[0...2]
p2192[0...2]
p2201[0...2]
p2202[0...2]
p2203[0...2]
p2204[0...2]
p2205[0...2]
p2206[0...2]
p2207[0...2]
p2208[0...2]
p2209[0...2]
p2210[0...2]
p2211[0...2]
p2212[0...2]
p2213[0...2]
p2214[0...2]
p2215[0...2]
p2216[0...2]
p2231[0...2]
p2240[0...2]
p2247[0...2]
p2248[0...2]
p2470[0...2]
p2481[0...2]
p2482[0...2]
p2484[0...2]
p2487[0...2]
p2488[0...2]
© Siemens AG 2007 All Rights Reserved
SINAMICS G120 Control Units CU240S, Edition 05/2007
Threshold current I_thresh / Threshold current
Delay time current / Delay time current
Threshold DC-link voltage / Vdc threshold
Delay time DC-link voltage / Vdc delay time
Torque threshold M_thresh / Torque threshold
Delay time for torque threshold / Delay time torque
Delay time for motor is blocked / Delay_T MotBlocked
Delay time for motor pulled out / Delay_T MotPullOut
Belt failure detection mode / Belt fail detect
Belt threshold frequency 1 / Belt threshold f_1
Belt threshold frequency 2 / Belt threshold f_2
Belt threshold frequency 3 / Belt threshold f_3
Upper torque threshold 1 / Upper trq. thresh1
Lower torque threshold 1 / Lower trq. thresh1
Upper torque threshold 2 / Upper trq. thresh2
Lower torque threshold 2 / Lower trq. thresh2
Upper torque threshold 3 / Upper trq. thresh3
Lower torque threshold 3 / Lower trq. thresh3
Time delay for belt failure / Belt fail delay_T
Fixed PID setpoint 1 / Fixed PID setp. 1
Fixed PID setpoint 2 / Fixed PID setp. 2
Fixed PID setpoint 3 / Fixed PID setp. 3
Fixed PID setpoint 4 / Fixed PID setp. 4
Fixed PID setpoint 5 / Fixed PID setp. 5
Fixed PID setpoint 6 / Fixed PID setp. 6
Fixed PID setpoint 7 / Fixed PID setp. 7
Fixed PID setpoint 8 / Fixed PID setp. 8
Fixed PID setpoint 9 / Fixed PID setp. 9
Fixed PID setpoint 10 / Fixed PID setp. 10
Fixed PID setpoint 11 / Fixed PID setp. 11
Fixed PID setpoint 12 / Fixed PID setp. 12
Fixed PID setpoint 13 / Fixed PID setp. 13
Fixed PID setpoint 14 / Fixed PID setp. 14
Fixed PID setpoint 15 / Fixed PID setp. 15
Fixed PID setpoint mode / Fix.PID Mode
PID-MOP mode / PID-MOP mode.
Setpoint of PID-MOP / Setp. of PID-MOP
PID-MOP ramp-up time of the RFG / PMOP ramp-up time
PID-MOP ramp-down time of the RFG / PMOP rampdown time
Encoder speed scaling factor / Encod speed scal
Gearbox ratio input / Gearbox ratio in
Gearbox ratio output / Gearbox ratio out
No. of shaft turns = 1 Unit / Position ref. unit
Positional error trim value / Positional trim / Positional error
Distance / No. of revolutions / Distance / No. rev
Command and Drive Data Sets – Overview
Parameters
1-305