Table of Contents
Advertisement
Show/Hide Bookmarks
Code
Code
Name
Name
C336*
Actual V
process
controller
C338*
Input 1,
arithmetic
block 2
C339*
Input 2,
arithmetic
block 2
C370*¤ Enable
automation
interface
C380*
n
speed
set
C381*
n
at
set
n-controller
C382*
Actual speed
C387*
Torque limit
C388*
Torque setpoint
C391*
Actual angle
C392*
Field current
setpoint
C393*
Additional
setpoint
C580*
Input 1,
comparator 1
C581*
Input 2,
limit value for
comparator 1
C582*
Hysteresis for
lower threshold
comparator 1
C583*
Memory
function
comparator 1
C584*¤ Reset function
comparator 1
Possible settings
Lenze
Selection
of the
0.1
p
0%
-100.0 %
-200 %{1 %}
0%
-100.0 %
-200 %
-0-
No communication via automation interface
-1-
Communication via automation interface
enabled
-16384
-32767
-32767
-16384
-16384
0
0
-16384
0 %
-100.0 %
-200 %
0 %
-100.0 %
-200 %
0 %
0.0 %
-0-
Memory function not active
when resettingthe output, the value falls below
the lower threshold (C581 - C582)
-1-
Memory function active
The output remains set after inital switching
on.
-0-
Reset function not active
-1-
Reset function active
Info
{0.1}
500.0
Display: Actual gain factor of the process
controller (important for process controller
adaption)
{0.1 %}
100.0 %
If an analog signal source (C145/C146) is
assigned, the parameter will be displayed
+200 %
only.
{0.1 %}
100.0 %
If an analog signal source (C145/C146) is
assigned, the parameter will be displayed
{1 %}
+200 %
only.
{1}
16384
High precision main setpoint selection:
16384 Ÿ 100% under C046
Input only via interface.
{1}
32767
High precision setpoint display:
Input of the speed controller,
16384 Ÿ 100% under C050.
Input only via interface.
{1}
32767
High precision display: Act. speed value
16384 Ÿ n
Input only via interface.
{1}
16384
High precision torque setpoint selection:
16384 Ÿ 100% under C047.
Input only via interface.
{1}
16384
High precision torque setpoint display:
16384 Ÿ 100% under C056.
Input only via interface.
{1}
65535
High precision display of the actual angle
if resolver or incremental encoder operate
as feedback system:
16384 Ÿ 360• Ÿ1 revolution.
Input only via interface.
{1}
16384
High precision display of the field current
setpoint:
16384 Ÿ I
Input only via interface.
{1}
16384
High precision additional setpoint display:
16384 Ÿ 100% under C049.
Input only via interface.
{0.1 %}
+100.0 %
If an analog signal source (C145/C146) is
assigned, the parameter will be displayed
{1 %}
+200 %
only.
{0.1 %}
+100.0 %
If an analog signal source (C145/C146) is
{1 %}
+200 %
assigned, the parameter will be displayed
only.
{0.1 %}
+100.0 %
Lower threshold = C581 - C582,
reference: C581
The activation resets the output.
Configuration
under C011.
max
under C083.
FN
48XX/49XXSHB0399
7-141
Hide quick links:
Advertisement
Table of Contents
