Lenze 4800 Manual page 226

Show/Hide Bookmarks
Code Code Name Name
C148 Additional
torque value 1
C149 Additional
torque value 2
C151* FDO
Status
[C180*] 4Q/2Q
operation
C182* T time of the
i
S-shape
ramp function
generators
C183 Origin of
controller inhibit
C185 Motor power
C186 Motor torque
C187 Field current
setpoint
C188 Actual field
current
C189 Mains
frequency
C190*¤ Arithmetic
block 1
C191*¤ Arithmetic
block 2
Possible settings
Lenze Selection
0 -100.0 % M {0.1%}
max
-200 % M {1%}
max
0 -100.0 % M {0.1%}
max
-200 % M {1%}
max
Bit Free digital output
0 FDO 1
...
11 FDO 12
12 Relay output
-0- 4Q operation (49XX)
-1- 2Q operation (48XX)
20.0 s 0.01 s {0.01s}
1s {0.1s}
10s {1s}
Display Origin of ctrl inhibit
Terminal or term. Terminal
Keypad or kp Keypad (STP key)
LECOM1 or L1 LECOM1 interface
Aut.int. (AIF) Automation / fieldbus interface
(module, InterBus, PROFIBUS, ...)
oth. src. Other source
or o.s. Release: TRIP or message
Information: C065, C067
-500.0 kW {0.1 kW}
-999 Nm {1 Nm}
0.00 A {0.01 A}
0.00 A {0.01 A}
0.0 Hz {0.1 Hz}
1 -0- Output = C046
-1- Output = C046 + C049
-2- Output = C046 - C049
Output = C046 ¼ C049
-3-
-4- Output = C046 / |C049|
-5- Output = C046 / (100% - C049)
1 -0- Output = C338
-1- Output = C338 + C339
-2- Output = C338 - C339
Output = C338 ¼ C339
-3-
-4- Output = C338 / |C339|
-5- Output = C338 / (100% - C339)
Configuration
Info
+100.0 % M Display only with terminal control. If the
max
terminal control is deactivated, the actual
+200 % M
max
terminal value will be accepted for
opera tion. Armature setting range: 100 %
M correspond to 100 % I
max
C023)
+100.0 % M Display only with terminal control. If the
max
terminal control is deactivated, the actual
+200 % M
max
terminal value will be accepted for
opera tion. Armature setting range: 100 %
M correspond to 100 % I
max
(C022/C023)
C151 indicates the states of the digital
outputs as decimal or binary values. The
polarity reversal under C118 is not
considered.
Important for controller type 48XX:
Controllers must only be operated with
C180 = -1-!
Fault PR sets C180 = -0-. It is absolutely
necessary to set C180 = -1- before
commissioning.
1 s T time for the S-shape ramp function
i
generator of the main setpoint
10s
50s
Display: Source which has inhibited the
controller
500.0 kW Display: actual motor power
999 Nm Display: actual motor torque
50.0 A Display: actual field current setpoint
50.0 A Display: actual field current value
100.0 Hz Display: actual mains frequency
(C022,
max
max
48XX/49XXSHB0399
7-135