D-Link DGS-510 Reference Manual page 56

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
ADDR | DST-IP-ADDR DST-IP-WILDCARD} [{eq | lt | gt | neq} PORT | range MIN-PORT MAX-
PORT] [TCP-FLAG] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range
PROFILE-NAME]
[SEQUENCE-NUMBER] {permit | deny} udp {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-
IP-WILDCARD} [{eq | lt | gt | neq} PORT | range MIN-PORT MAX-PORT] {any | host DST-IP-
ADDR | DST-IP-ADDR DST-IP-WILDCARD} [{eq | lt | gt | neq} PORT | range MIN-PORT MAX-
PORT] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-NAME]
[SEQUENCE-NUMBER] {permit | deny} icmp {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-
IP-WILDCARD} {any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD} [ICMP-TYPE
[ICMP-CODE] | ICMP-MESSAGE] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP]
[time-range PROFILE-NAME]
[SEQUENCE-NUMBER] {permit | deny} {gre | esp | eigrp | igmp | ipinip | ospf | pcp | pim |
vrrp | protocol-id PROTOCOL-ID} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-
WILDCARD} {any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD} [fragments]
[[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-NAME]
[SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-
WILDCARD} [any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD] [fragments]
[[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-NAME]
Standard IP Access List:
[SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-
WILDCARD} [any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD] [time-range
PROFILE-NAME]
no SEQUENCE-NUMBER
Parameters
SEQUENCE-NUMBER
any
host SRC-IP-ADDR
SRC-IP-ADDR SRC-IP-
WILDCARD
host DST-IP-ADDR
DST-IP-ADDR DST-IP-
WILDCARD
precedence PRECEDENCE
dscp DSCP
tos TOS
lt PORT
gt PORT
eq PORT
Specifies the sequence number. The range is from 1 to 65535. The
lower the number is, the higher the priority of the permit/deny rule.
Specifies any source IP address or any destination IP address.
Specifies a specific source host IP address.
Specifies a group of source IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
Specifies a specific destination host IP address.
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
(Optional) Specifies that packets can be filtered by precedence
level, as specified by a number from 0 to 7.
(Optional) Specifies the matching DSCP code in IP header. The
range is from 0 to 63, or select the following DSCP name: af11 -
001010, af12 -001100, af13 - 001110, af21 - 010010, af22 -
010100, af23 - 010110, af31 - 011010, af32 - 011100, af33 -
011110, af41 - 100010, af42 - 100100, af43 - 100110, cs1 - 001000,
cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 -
110000, cs7 - 111000, default - 000000, ef – 101110.
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
(Optional) Specifies to match if less than the specified port number.
(Optional) Specifies to match if greater than the specified port
number.
(Optional) Specifies to match if equal to the specified port number.
53