D-Link DGS-510 Reference Manual page 54

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
vlan-range MIN-VID MAX-VID
vlan OUTER-VLAN
any
host SRC-MAC-ADDR
SRC-MAC-ADDR SRC-MAC-
WILDCARD
host DST-MAC-ADDR
DST-MAC-ADDR DST-MAC-
WILDCARD
PROTOCOL
host SRC-IP-ADDR
SRC-IP-ADDR SRC-IP-
WILDCARD
host DST-IP-ADDR
DST-IP-ADDR DST-IP-
WILDCARD
precedence PRECEDENCE
tos TOS
dscp DSCP
lt PORT
gt PORT
eq PORT
neq PORT
range MIN-PORT MAX-PORT
TCP-FLAG
fragments
time-range PROFILE-NAME
ICMP-TYPE
ICMP-CODE
(Optional) Specifies the VLAN range. Enter the minimum and
maximum VLAN ID in the range here.
(Optional) Specifies the outer VLAN ID.
Specifies to use any source MAC address, any destination MAC
address, any source IP address, or any destination IP address.
Specifies a specific source host MAC address.
Specifies a group of source MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to bit value 0 will be checked.
Specifies a specific destination host MAC address.
Specifies a group of destination MAC addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
(Optional) Specifies the IP protocol ID. Enter the following
keywords: eigrp, esp, gre, igmp, ospf, pim, vrrp, pcp, and ipinip.
Specifies a specific source host IP address.
Specifies a group of source IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
Specifies a specific destination host IP address.
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
(Optional) Specifies that packets can be filtered by precedence
level, as specified by a number from 0 to 7.
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
(Optional) Specifies the matching DSCP code in IP header. The
range is from 0 to 63, or select the following DSCP name: af11 -
001010, af12 -001100, af13 - 001110, af21 - 010010, af22 -
010100, af23 - 010110, af31 - 011010, af32 - 011100, af33 -
011110, af41 - 100010, af42 - 100100, af43 - 100110, cs1 -
001000, cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000,
cs6 - 110000, cs7 - 111000, default - 000000, ef – 101110.
(Optional) Specifies to match if less than the specified port number.
(Optional) Specifies to match if greater than the specified port
number.
(Optional) Specifies to match if equal to the specified port number.
(Optional) Specifies to match if not equal to the specified port
number.
(Optional) Specifies to match if fall within the range of ports.
(Optional) Specifies the TCP flag fields and the specified TCP
header bits called ack (acknowledge), fin (finish), psh (push), rst
(reset), syn (synchronize), or urg (urgent).
(Optional) Specifies the packet fragment's filtering.
(Optional) Specifies the name of time period profile associated with
the access list delineating its activation period.
(Optional) Specifies the ICMP message type. The valid number for
the message type is from 0 to 255.
(Optional) Specifies the ICMP message code. The valid number for
the message code is from 0 to 255.
51