HPE FlexFabric 5930 Series Network Management And Monitoring Command Reference page 17

-q packet-number: Specifies the number of probe packets to send per hop. The value range is 1 to
65535, and the default is 3.
-t tos: Specifies the ToS value of probe packets. The value range is 0 to 255, and the default is 0.
-vpn-instance vpn-instance-name: Specifies the MPLS L3VPN instance to which the destination
belongs, where the vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. If
the destination is on the public network, do not specify this option.
-w timeout: Specifies the timeout time in milliseconds of the reply packet for a probe packet. The
value range is 1 to 65535, and the default is 5000.
host: Specifies the IP address or host name of the destination. The host name is a case-insensitive
string of 1 to 253 characters, which can contain letters, digits, and special characters such as hyphen
(-), underscore (_), and dot (.). It cannot be i, ip, ipv, ipv6, m, mp, mpl, or mpls.
Usage guidelines
After identifying network failure with the ping command, use the tracert command to locate failed
nodes.
The output of the tracert command includes IP addresses of all the Layer 3 devices that the packets
traverse from source to destination. Asterisks (* * *) are displayed if the device cannot reply with an
ICMP error message. The reason might be the destination is unreachable or sending ICMP
timeout/destination unreachable packets is disabled).
To abort the tracert operation during the execution of the command, press Ctrl+C.
Examples
# Display the path that the packets traverse from source to destination (1.1.2.2).
<Sysname> tracert 1.1.2.2
traceroute to 1.1.2.2(1.1.2.2), 30 hops at most, 40 bytes each packet, press CTRL_C to
break
1 1.1.1.2 (1.1.1.2) 673 ms 425 ms 30 ms
2 1.1.2.2 (1.1.2.2) 580 ms 470 ms 80 ms
# Trace the path to destination (192.168.0.46) over an MPLS network.
<Sysname> tracert 192.168.0.46
traceroute to 192.168.0.46(192.168.0.46), 30 hops at most, 40 bytes each packet, press
CTRL_C to break
1 192.0.2.13 (192.0.2.13)
2 192.0.2.9 (192.0.2.9)
MPLS Label=100048 Exp=0 TTL=1 S=1
3 192.0.2.5 (192.0.2.5)
MPLS Label=100016 Exp=0 TTL=1 S=1
4 192.0.2.1 (192.0.2.1)
Table 2 Command output
Field
traceroute to 1.1.2.2(1.1.2.2)
hops at most
bytes each packet
press CTRL_C to break
1 1.1.1.2 (1.1.1.2) 673 ms
0.661 ms 0.618 ms
0.861 ms 0.718 ms
0.822 ms 0.731 ms
0.961 ms 8.676 ms
Description
Display the route that the IP packets traverse from the current device to the
device whose IP address is 1.1.2.2.
Maximum number of hops of the probe packets, which can be set by the -m
keyword.
Number of bytes of a probe packet.
During the execution of the command, press Ctrl+C to abort the tracert
operation.
Probe result of the probe packets whose TTL is 1, including the domain
8
0.579 ms
0.679 ms
0.708 ms
0.875 ms