Spindle Data - Siemens SINUMERIK 840Di Manual

10 NC Start-Up with HMI Advanced
10.5 Axes and spindles

10.5.28 Spindle data

Machine data
Table 10-47 Spindle: Machine data
Number
General ($MN_ ...)
12060 OVR_SPIND_IS_GRAY_CODE
12070 OVR_FACTOR_SPIND_SPEED
12080 OVR_REFERENCE_IS_PROG_FEED
Channel-specific ($MC_ ...)
20090 SPIND_DEF_MASTER_SPIND
20092 SPIND_ASSIGN_TAB_ENABLE
20118 GEOAX_CHANGE_RESET
22400 S_VALUES_ACTIVE_AFTER_RESET
Axis-specific ($MA_ ...)
30300 IS_ROT_AX
30310 ROT_IS_MODULO
30320 DISPLAY_IS_MODULO
31050 DRIVE_AX_RATIO_DENOM
31060 DRIVE_AX_RATIO_NUMERA
31122 BERO_DELAY_TIME_PLUS
31123 BERO_DELAY_TIME_MINUS
32200 POSCTRL_GAIN
32810 EQUIV_SPEEDCTRL_TIME
32910 DYN_MATCH_TIME.
34040 REFP_VELO_SEARCH_MARKER
34060 REFP_MAX_MARKER_DIST
34080 REFP_MOVE_DIST
34090 REFP_MOVE_DIST_CORR
34100 REFP_SET_POS
34200 ENC_REFP_MODE
35000 SPIND_ASSIGN_TO_MACHAX
35010 GEAR_STEP_CHANGE_ENABLE
35012 GEAR_STEP_CHANGE_POSITION
35020 SPIND_DEFAULT_MODE
35030 SPIND_DEFAULT_ACT_MASK
35040 SPIND_ACTIVE_AFTER_RESET
35100 SPIND_VELO_LIMIT
35110 GEAR_STEP_MAX_VELO[n]
35120 GEAR_STEP_MIN_VELO[n]
35130 GEAR_STEP_MAX_VELO_LIMIT[n]
35140 GEAR_STEP_MIN_VELO_LIMIT[n]
35150 SPIND_DES_VELO_TOL
35160 SPIND_EXTERN_VELO_LIMIT
35200 GEAR_STEP_SPEEDCTRL_ACCEL[n]
10-376
Identifier Name
Spindle override, Gray-coded
Evaluation of the spindle speed override switch
Override reference speed
Initial setting of master spindle in the channel
Enable/disable spindle converter
Permit automatic geometry axis change
S function effective with RESET
Rotary axis
Modulo conversion
Position display
Load gear denominator
Load gear numerator
BERO delay time in plus direction
BERO delay time in minus direction
KV factor
Equivalent time constant of speed control loop
for feedforward control
Time constant of dynamic adaptation
Reference shutdown speed
Monitoring of zero reference mark distance
Reference point distance/target position with
clearance-coded system
Reference point offset/absolute offset
clearance-coded
Reference point value
Referencing mode
Assignment of spindle to machine axis
Gear stage change possible
Gear stage change position
Spindle park position
Activate spindle park position
Spindle activated by reset
Max. spindle speed
Max. speed for gear stage change
Min. speed for gear stage change
Max. speed of gear stage
Min. speed of gear stage
Spindle speed tolerance
Spindle speed limiting from PLC
Acceleration in speed control mode
 Siemens AG, 2003. All rights reserved
SINUMERIK 840Di Manual (HBI) – 06.03 Edition
06.03
Ref.
V1
V1
V1
R2
R2
R2
G2
G2
G2
K3
G2
R1
R1
R1
R1
R1
R1