Download  Print this page
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552

Advertisement

06.03
SIMODRIVE 611
universal
Machine data
Table 10-41
Speeds and setpoint adjustment for spindle: Machine data
Axis-specific ($MA_ ...)
31050
DRIVE_AX_RATIO_DENOM
31060
DRIVE_AX_RATIO_NUMERA
32010
JOG_VELO_RAPID
32020
JOG_VELO
35010
GEAR_STEP_CHANGE_ENABLE
35020
SPIND_DEFAULT_MODE
35030
SPIND_DEFAULT_ACT_MASK
35040
SPIND_ACTIVE_AFTER_RESET
35200
GEAR_STEP_SPEEDCTRL_ACCEL[n]
35220
ACCEL_REDUCTION_SPEED_POINT
35230
ACCEL_REDUCTION_FACTOR
35400
SPIND_OSCILL_DES_VELO
35410
SPIND_OSCILL_ACCEL
35430
SPIND_OSCILL_START_DIR
35440
SPIND_OSCILL_TIME_CW
35450
SPIND_OSCILL_TIME_CCW
Interface signals
Table 10-42
Speeds and setpoint adjustment for spindle: Interface signals
DB number
Bit, Byte
Axis-specific
31, ...
4.6
31, ...
4.7
 Siemens AG, 2003. All rights reserved
SINUMERIK 840Di Manual (HBI) – 06.03 Edition
Drive parameter P0880: PROFIBUS speed evaluation
Speed n
Normalization value
P0880
Fig. 10-30 Speed setpoint normalization
The desired speed on the spindle is obtained using a mechanical gear stage.
Signals from PLC to axis/spindle
Traversing keys minus
Traversing keys plus
10 NC Start-Up with HMI Advanced
4000H
speed setpoint (low resolution)
4000 0000H speed setpoint (high resolution)
Load gear denominator
Load gear numerator
Conventional rapid traverse
Conventional axis velocity
Gear stage change possible
Spindle park position
Activate spindle park position
Spindle activated by reset
Acceleration in speed control mode
Speed limit for reduced acceleration
Reduced acceleration
Oscillation speed
Acceleration on oscillation
Start direction on oscillation
Oscillation time for M3 direction
Oscillation time for M4 direction
Name
10.5 Axes and spindles
G2
G2
Ref.
10-369

Advertisement

   Related Manuals for Siemens SINUMERIK 840Di

Comments to this Manuals

Symbols: 0
Latest comments: