Page 1 Instruction Manual DVC6200f Digital Valve Controller D103412X012 February 2017 ™ ™ Fisher FIELDVUE DVC6200f Digital Valve Controller for F Fieldbus ™ OUNDATION This manual applies to: Device Type 4602 Device Revision Hardware Revision 8, 9 Firmware Revision DD Revision Instrument Level FD, PD, AD, PST www.Fisher.com...
Page 2 Instruction Manual DVC6200f Digital Valve Controller D103412X012 February 2017...
Page 3: Table Of Contents
Instruction Manual DVC6200f Digital Valve Controller D103412X012 February 2017 Contents Sensor Alerts ......Environment Alerts .
Page 4: Using This Manual
Instruction Manual DVC6200f Digital Valve Controller D103412X012 February 2017 Section 8 Parts ..... Device Descriptions ......Transducer Block Status and Limit Propagation Parts Ordering .
Page 5: Section 1 Introduction And Specifications
DVC6200f digital valve controller. Note All references to the DVC6200f digital valve controller include the DVC6205f base unit unless otherwise indicated. This manual describes device setup using a Field Communicator. For information on using Fisher ValveLink ™ software with the instrument, refer to the appropriate user guide or help.
Page 6 DVC6200f digital valve controllers can be mounted on single or double‐acting sliding‐stem actuators, as shown in figure 1‐1, or on rotary actuators. It can also be integrally mounted to Fisher 657/667 size 30i to 76i actuators or the Fisher GX control valve and actuator system, as shown in figure 1‐2. The DVC6200f mounts on most Fisher and other manufacturers' rotary and sliding‐stem actuators.
Page 7 DVC6200f Digital Valve Controller Instruction Manual Introduction and Specifications D103412X012 February 2017 Instrument Blocks The digital valve controller is a block‐based device. For detailed information on the blocks within the digital valve controller, see the Detailed Setup section of this manual. The DVC6200f digital valve controller includes the resource and transducer block: D Resource Block—The resource block contains the hardware specific characteristics associated with a device;...
Page 8: Specifications
DVC6200f Digital Valve Controller Instruction Manual Introduction and Specifications February 2017 D103412X012 Using This Manual Navigation paths and fast‐key sequences are included for procedures and parameters that can be accessed using the Field Communicator. For example, to access Resource Block Mode: RB >...
Page 9 DVC6200f digital valve controller and DVC6215 Voltage Level: 9 to 32 volts feedback unit: J Integral mounting to 657/667 or Maximum Current: 19 mA GX actuators J Integral mounting to Fisher rotary Reverse Polarity Protection: Unit is not polarity actuators, J Sliding‐stem linear applications sensitive Quarter‐turn rotary applications...
Page 10 DVC6200f Digital Valve Controller Instruction Manual Introduction and Specifications February 2017 D103412X012 Table 1‐1. Specifications (continued) (2)(3) Steady-State Air Consumption Humidity Testing Method Tested per IEC 61514-2 Standard Relay At 1.4 bar (20 psig) supply pressure: Less than 0.38 normal m /hr (14 scfh) Electrical Classification At 5.5 bar (80 psig) supply pressure:...
Page 11 Stainless Steel: 8.6 kg (19 lbs) Declaration of SEP DVC6205f: 4.1 kg (9 lbs) DVC6215: 1.4 kg (3.1 lbs) Fisher Controls International LLC declares this product to be in compliance with Article 4 paragraph Construction Materials 3 of the PED Directive 2014/68/EU. It was designed...
Page 12: Related Information
D Bulletin 62.1:DVC6200f PST - DVC6200f Digital Valve Controller - PST Instrument Level (D104160X012) D Bulletin 62.1:DVC6200(S1) - DVC6200 Digital Valve Controller Dimensions (D103543X012) D Fisher FIELDVUE DVC6200 Series Quick Start Guide (D103556X012) D CSA Hazardous Area Approvals - DVC6200 Series Digital Valve Controllers (D104203X012) D FM Hazardous Area Approvals - DVC6200 Series Digital Valve Controllers (D104204X012)
Page 13: Section 2 Wiring Practices
DVC6200f Digital Valve Controller Instruction Manual Installation Information D103412X012 February 2017 Section 2 Wiring Practices 2-2- Quick Connect Cable Entry The DVC6200f is offered with a quick connect cable entry option, shown in figure 2‐1, for the Fieldbus OUNDATION signal. The quick connect cable entry provides an easier and more reliable interface to fieldbus devices and support modules by providing a standard connection.
Page 14: Communication Connections
DVC6200f Digital Valve Controller Instruction Manual Installation Information D103412X012 February 2017 d. The instrument is not polarity sensitive. Refer to figure 2‐2. Connect the blue wire to the negative (-) LOOP terminals in the terminal box. Connect the brown wire to the positive (+) LOOP terminal. Isolate the green/yellow wire inside of the DVC6200f and ensure that the shield is totally isolated at the instrument end.
Page 15: Simulate Enable Jumper
DVC6200f Digital Valve Controller Instruction Manual Installation Information D103412X012 February 2017 Simulate Enable Jumper WARNING Personal injury or property damage caused by fire or explosion may occur if this connection is attempted in a potentially explosive atmosphere or in an area that has been classified as hazardous. Confirm that area classification and atmosphere conditions permit the safe removal of the terminal box cap before proceeding.
Page 16 DVC6200f Digital Valve Controller Instruction Manual Installation Information D103412X012 February 2017...
Page 17: Section 3 Basic Setup
DVC6200f Digital Valve Controller Instruction Manual Basic Setup D103412X012 February 2017 Section 3 Basic Setup3-3- Basic Setup Field Communicator TB > Configure/Setup > Basic Setup WARNING Changes to the instrument setup may cause changes in the output pressure or valve travel. Depending on the application, these changes may upset process control, which may result in personal injury or property damage.
Page 18: Device Setup
DVC6200f Digital Valve Controller Instruction Manual Basic Setup D103412X012 February 2017 Device Setup Field Communicator TB > Configure/Setup > Basic Setup > Device Setup Follow the prompts on the Field Communicator display to automatically setup the instrument using specified actuator information.
Page 19 (Window-mount) 60, 70 Depends upon pneumatic connections. See 1061 Piston Dbl w/o Spring description for Travel Sensor Motion Fisher 68, 80, 100, 130 Mounting Style Travel Sensor Motion Away from the top of the instrument Towards the top of the...
Page 20 Relay A adjustment may be required before Device Setup can determine travel sensor motion. Follow the prompts on the Field Communicator display if relay adjustment is necessary. Table 3‐2 lists the required Travel Sensor Motion selections for Fisher and Baumann actuators.
Page 21 Stabilize/Optimize or Performance Tuner may be used to achieve the desired results more rapidly than expert tuning. Table 3‐2 provides tuning set selection guidelines for Fisher and Baumann actuators. These tuning sets are only recommended starting points. After you finish setting up and calibrating the instrument, use Stabilize/Optimize to...
Page 22: Performance Tuner
DVC6200f Digital Valve Controller Instruction Manual Basic Setup D103412X012 February 2017 When Device Setup is complete you are asked if you wish to run Auto Calibration now. Select yes to automatically calibrate instrument travel at this time. Follow the prompts on the Field Communicator display. The calibration procedure uses the valve and actuator stops as the 0% and 100% calibration points.
Page 23: Section 4 Detailed Setup
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Section 4 Detailed Setup 4-4- Resource Block The resource block contains the hardware specific characteristics associated with a device; it has no input or output parameters. The resource block monitors and controls the general operation of other blocks within the device. Most of the resource block parameters are operational parameters that provide information about the instrument such as identification, hardware information, available options, etc.
Page 24: Communication Timeout
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Communication Timeout Shed Remote Cascade Note Typically this parameter does not need to be changed. The unit will be operational using the default values assigned by the factory. Perform this procedure only if a remote computer is sending setpoints from your “advanced”...
Page 25: Alarm Handling
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 D Multi‐bit Alarm (Bit‐Alarm) Support permits the instrument to treat each Field Diagnostic alert separately when broadcast to the Host. Without Multi‐Bit Alarm Support, an individual Field Diagnostic alert must be acknowledged before another Field Diagnostic alert can be broadcast to the Host.
Page 26: Identification
Manufacturer (MANUFAC_ID [10]) identifies the manufacturer of the instrument. It is used by the host system to locate the DD file for the device. For Fisher the Manufacturer ID is 0x5100. Device Type (DEV_TYPE [11]) identifies the type of device. It is used by the host system to locate the DD file for the device.
Page 27: Version
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Version Device Revision (DEV_REV [12]) is the manufacturer's revision number associated with the resource, used by an interface device to locate the DD file for the resource. Firmware Revision (FIRMWARE_REVISION [105]) identifies the revision of the firmware that is currently in use.
Page 28: Parameters Affected By Restart With Defaults
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Parameters Affected by Restart with Defaults Table 4‐1. Parameters Affected by Restart with Table 4‐2. Parameters Affected by Restart with Defaults Defaults Index Index Parameter Name Initial Value Parameter Name Initial Value...
Page 29 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐1. Parameters Affected by Restart with Table 4‐1. Parameters Affected by Restart with Defaults (Continued) Defaults (Continued) Index Index Parameter Name Initial Value Parameter Name Initial Value Number Number...
Page 30 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐1. Parameters Affected by Restart with Table 4‐1. Parameters Affected by Restart with Defaults (Continued) Defaults (Continued) Index Index Parameter Name Initial Value Parameter Name Initial Value Number Number...
Page 31 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐1. Table Parameters Affected by Restart with Table 4‐1. Parameters Affected by Restart with Defaults (Continued) Defaults (Continued) Index Index Parameter Name Initial Value Parameter Name Initial Value Number Number...
Page 32 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐1. Parameters Affected by Restart with Defaults (Continued) Index Parameter Name Initial Value Number Transducer Block ST_REV TAG_DESC Spaces STRATEGY ALERT_KEY MODE_BLK TARGET PERMITTED OOS, MAN, AUTO NORMAL AUTO FD_FAIL_MAP_2...
Page 33: Resoure Block Parameter List
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Resource Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter.
Page 34 The device type directories contain files named by combining the device revision for the particular device type with the revision of the device description. The manufacturer id for Fisher is 0x005100. Data Type: Unsigned16 Device Type Manufacturer's model number associated with...
Page 35 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value 0: Unicode 1: Reports 2: Faultstate Data Type: Bit String 3: Soft W Lock 0 = Inactive 5: Out Readback...
Page 36 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Date Type: Unsigned32 Time duration (in 1/32 millisecond) at which to give up on computer writes to function block RCAS Timeout RCAS parameters.
Page 37 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Data Type: Unsigned8 If set to Locked, no writes from anywhere are allowed except to clear WRITE_LOCK by entering Write Lock 1: Unlocked...
Page 38 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Data Type: Unsigned8 Priority of the alarm generated by setting WRITE_LOCK to Unlocked.
Page 39 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Continued from Data Type: Bit String, 4 bytes previous page: Alert is the act of detecting a condition in the 25: FST Pass dev device.
Page 40 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Data Type: Bit String, 4 bytes 0 = Disable AUTO All Disabled 1 = Enable...
Page 41 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Data Type: DS-87Alarm is the message notifying FD_CHECK_ALM a host of an Alert condition. 0: Uninitialized AUTO 1: Acknowledged...
Page 42 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Compatibility Revision Data Type: Uint8 COMPATIBILITY_REV Data Type: Uint8 Hardware Revision Describes electronic hardware revision HARDWARE_REVISION...
Page 43 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value Data Type: Bit String, 4 bytes Copy of FD_FAIL_MASK. *See FD_FAIL_MASK for Range and Initial Value.
Page 44 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐3. Resource Block Parameter Definitions Label Index RO / Initial Mode Range Description PARAMETER_NAME Number Value 1: FD 2: AD 3: PD Data Type: Uint8 4: SIS Diagnostic Options Indicates which diagnostics licensing options are...
Page 45: View Lists
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 46 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Resource Block D103412X012 February 2017 Table 4‐4. Resource Block, View Lists (Continued) View Index Number Parameter FD_OFFSPEC_ACTIVE FD_MAINT_ACTIVE FD_CHECK_ACTIVE FD_FAIL_MAP FD_OFFSPEC_MAP FD_MAINT_MAP FD_CHECK_MAP FD_FAIL_MASK FD_OFFSPEC_MASK FD_MAINT_MASK FD_CHECK_MASK FD_FAIL_PRI FD_OFFSPEC_PRI FD_MAINT_PRI FD_CHECK_PRI FD_SIMULATE FD_RECOMMEN_ACT FD_EXTENDED_ACTIVE_1...
Page 47: Transducer Block
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Transducer Block The transducer block accepts a signal from an output block as a set point to position a valve using a pneumatic actuator. Input to the transducer block is in percent. Closed is 0%, and open is 100%. The transducer block contains setup and calibration information and can be tuned to closely match the actuator.
Page 48: Response Control
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 d Calibration will protect only Calibration transducer block parameters. d Setup and Calibration will protect only Setup and Calibration transducer block parameters. d All— will protect all transducer block Parameters. Note The Device Setup Auto Travel and Manual Travel methods automatically change transducer block protection for the user.
Page 49 Stabilize/Optimize may be used to achieve the desired results more rapidly than manually editing the Expert tuning. Table 3‐2 provides tuning set selection guidelines for Fisher and Baumann actuators. These tuning sets are recommended starting points. After you finish setting up and calibrating the instrument, you may have to select either a higher or lower tuning set to get the desired response.
Page 50: Pressure Tuning
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Stabilize/Optimize WARNING During Stabilize/Optimize the valve may move, causing process fluid or pressure to be released. To avoid personal injury and property damage caused by the release of process fluid or pressure, isolate the valve from the process and equalize pressure on both sides of the valve or bleed off the process fluid.
Page 51: Travel Pressure Control
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐6. Gain Values for Preselected Pressure Tuning Sets Tuning Set Pressure Proportional Gain Pressure Integrator Gain Pressure Minor Loop Feedback Gain X (Expert) User Adjusted User Adjusted User Adjusted Note...
Page 52 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Note Travel / Pressure Select must be set to Travel for double acting actuators. Travel / Pressure Select determines if the instrument is setup for position or pressure control. Select Travel, Pressure, Travel with Pressure Fallback/Auto recovery or Travel with Pressure Fallback/Manual Recovery.
Page 53: Characterization
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Characterization Characterization (INPUT_CHAR [76]) defines the relationship between the travel target and the setpoint received from the output block. Travel target is the output from the characterization function. You can select from the three fixed input characteristics shown in figure 4‐1 or you can select a custom characteristic.
Page 54: Output Block Selection
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Output Block Selection Output Block Selection (OUTBLOCK_SEL [112]) defines which output function block (AO or DO) will control the setpoint of the valve. The output block that is not selected will shed its mode to reflect that it does not have control of the valve.
Page 55: Field Diagnostic Alert Category
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Field Diagnostic (FD) Alert Category Select either Enable or Suppress in the desired category for each of the alerts in Electronic, Configuration, Sensor, Environment, Travel, Proximity, Travel History, Test Overdue, Performance, and Valve Stroke: Fail Enable (FD_FAIL_MAP_2 [86]) enables or disables conditions that can cause a failed alert.
Page 56 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 D Drive Current Shutdown—The Shutdown Trigger (SHUTDOWN_TRIGGER [83.1]) permits enabling or disabling Self Test Shutdown for the Drive Current alert. When enabled, and the alert condition is present, the transducer Actual mode is placed Out of Service.
Page 57: Configuration Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Manual or Auto. In any case, the target mode will remain Out of Service, if the condition that caused the shutdown remains or until the shutdown trigger is disabled. D The Static Memory Alert is active if a failure occurs in the FRAM memory where the static parameters are stored.
Page 58: February 2017
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Blocks Set to Default D The Blocks Set to Defaults Alert is active if the resource block has undergone Restart with Defaults. This will stay active until the transducer block is changed from Out of Service. Check Alert FD Alert Config The Alert Key (ALERT_KEY [4]) is the identification number of the plant unit.
Page 59: Environment Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Pressure Fallback D The Pressure Fallback Alert is active if a travel sensor failure or a gross travel deviation has resulted in fallback to pressure control. D Pressure Fallback FD Config Temperature Sensor D The Temperature Sensor Alert is active if the Temperature Sensor reading is outside the functional range.
Page 60: Travel Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Travel Alerts Note The alerts contained in this section are valid for both travel and pressure control. Working Setpoint is the output from the characterization function. Travel (DeChar) (FINAL.VALUE [14.2]) displays the actual position of the valve in percent (%) of calibrated travel.
Page 61: Proximity Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 D The Travel Limit Low Low Alert alert is active if the Travel is lower than the Travel Lo Lo Alert point. D Travel Lo Lo Alert Point (TVL_LO_LO_ALRT_PT [84.8])— The Travel Lo Lo alert is set when the value of the travel, in percent (%) of ranged travel, goes below the Travel Lo Lo Alert Point.
Page 62: Travel History Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Travel Open D The Travel Open Alert is active if the Travel is greater than the Travel Open Alert Point. D Travel Open Alert Point (STOP_HI_POS [27]) is the value of the travel in percent (%) or ranged travel, which, when exceeded, sets the Travel Open Alert.
Page 63 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Figure 4‐4. Cycle Counter Deadband (set at 10%) Deadband exceeded, and direction changed, new Reference Point established Point at which cycle is counted Deadband Reference Point Deadband (+/- 5%) A6533‐1 Travel Accumulator...
Page 64 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Figure 4‐5. Travel Accumulator Deadband (set at 10%) Deadband exceeded, new Reference Point established This amount of change is Deadband Reference added to the Travel Point Accumulator Deadband (+/- 5%) A6534...
Page 65: Performance Alerts
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Performance Alerts Note Performance Alerts are only available with a PD or a PST instrument. Additionally, for the PD alerts to function properly: The transducer block mode must not be out of service. ...
Page 66 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 FST Abnormal D FST Abnormal Alert D FST Abnormal FD Config FST Pass D FST Pass Alert D FST Pass FD Config PST Pending D PST Pending Alert D Auto PST Alert Time D PST Pending FD Config Stroke Test Overdue D PST Overdue Alert...
Page 67: Alert Handling
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Alert Handling Field Communicator TB > Configure/Setup > Detailed Setup > Alert Handling Output Block - Echo Block Err— when enabled, the AO or DO BLOCK_ERR [6] parameter will report Field Diagnostic Alerts.
Page 68: Instrument
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Instrument Field Communicator TB > Configure/Setup > Detailed Setup > Instrument Tag Description (TAG_DESC [2]) is used to assign a unique description to each block within the digital valve controller to describe the intended application for the block.
Page 69: Valve And Actuator
Select from the drop‐down list or enter the manufacturer's identification number as defined by the Fieldbus Foundation. For Fisher, the manufacturer ID hex value is 005100. D Enter the Valve Model Number (VALVE_MODEL_NUM [52]), (design letter or type number) for the valve on which the instrument is mounted.
Page 70 Select from the drop‐down list or enter the manufacturer's identification number as defined by the Fieldbus Foundation. For Fisher, the manufacturer ID hex value is 005100. D Enter the Actuator Model Number (ACT_MODEL_NUM [48]) on which the instrument is mounted.
Page 71 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 D Travel Sensor Motion (TRAVEL_SENSOR_MOTION [67.3]) WARNING Setting the Travel Sensor Motion incorrectly may cause the valve to move. To avoid personal injury and property damage caused by the release of pressure or process fluid, isolate the valve from the process and equalize pressure on both sides of the valve or bleed off the process fluid.
Page 72: Mai Channel Map
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 D Enter valve Trim Style 2 (TRIM_STYLE_2 [101.10]). MAI Channel Map TB > TB > Configure/Setup > Detailed Setup > MAI Channel Map Field Communicator Allows the user to specify which transducer block parameter is available through each of the MAI Block channels (MAI_CHANNEL_1 through MAI_CHANNEL_8 [111.1 through 111.8]).
Page 73 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 D Test Pause Time (VST_PAUSE [120]) is the time between the outgoing and incoming strokes of the test. The default value is 5 seconds. Pause Time will not be used if Minimum PST Pause Time is enabled. The outgoing stroke is from the normal end to the PST target and the incoming stroke is the return stroke to normal.
Page 74 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 3. Incoming Pressure Threshold 4. High Friction Breakout Pressure 5. Low Friction Breakout Pressure D VST Abort Criteria (VST_ABORT_CRITERIA [129.2]) The PST is terminated and the valve is returned to the normal end. The return to the normal end will be per the user configuration for an aborted test.
Page 75 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Figure 4‐7. Time Series Representation of Minimum PST Pause Time NORMAL NORMAL INCOMING OUTGOING RAMP RATE RAMP RATE REDUCED PST TIME RETURN LEAD RETURN SETPOINT LEAD OVERDRIVE SETPOINT OVERDRIVE...
Page 76 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 1. Connect the DVC6200f to a system running ValveLink software. 2. Disable Partial Stroke Outgoing Pressure Limit by ensuring it is not selected as an evaluation criteria for PST Abnormal.
Page 77 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 VST Incoming Pressure Threshold defines the actuator pressure at which a partial stroke test will abort during the incoming stroke (see figure 4‐6). This prevents the DVC6200f from exhausting (or building) excessive pressure from / to the actuator in an attempt to move a stuck valve.
Page 78: Latch
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Latch Field Communicator TB > Configure/Setup > Detailed Setup > Latch Reset Latch Latch State (LATCH_STATE [180]) specifies if a latch is active. Latch Reset Options (LATCH_RESET_OPTS [182]) perform a manual reset by pushing the reset button in the user interface after ensuring the normalcy of the output block and supply pressure.
Page 79: Transducer Block Parameter List
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Transducer Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Protection Category: Indicates whether or not the parameter is writable while the PROTECTION parameter is set to a particular level.
Page 80 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 0: Uninitialized Data Type: DS‐73 UPDATE_STATE 1: Reported Alert generated by change to static 2: Not reported data.
Page 81 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: Float When the servo goes below this % of Travel Cutoff Lo span, the stem position goes to the -25 to 125, -INF...
Page 82 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 32.2 NONE Data Type: UINT8 VALUE Data Type: DS-66 FINAL_POSITION_VALUE_D 33.1 Data Type: UINT8...
Page 83 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Continued from previous page: 75: Mark Crossover (Protection = Calibration) 76: Cal Abort/ Performance...
Page 84 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Continued from previous page: 100: Performance Tuner - Active 101: Performance Tuner - Moving...
Page 85 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 0: Globe 1: Gate 2: Butterfly 3: Ball AUTO Valve Style 4: Plug...
Page 86 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category PRESSURE_B Data Type: DS-65 Good Process Non STATUS indicates the validity of Pressure B Status 63.1...
Page 87 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 1 = Relay A or C -- Double or Single Direct 2 = Relay B -- Single Reverse...
Page 88 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 70.2 0 - 150 psi SETUP Data Type: Float ENDPT_PRESS_SETPT 70.3 0 - 15 min...
Page 89 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 72.10 0 - 1 SETUP Data Type: Float TVL_PRESS_RATE_FILT PRESS_CAL Supply Pressure Scale...
Page 90 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Drive Current 0 to 100% Data Type: Float DRIVE_CURRENT MLFB -100 to 100%...
Page 91 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Bit 18: PST Anomaly Bit 19: FST Anomaly Bit 21: PST Success Bit 22: FST Success Data Type: Bit String...
Page 92 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Bit 0: I/P Primary Plugging (High I/P 1d_y) Bit 1: I/P Nozzle Plugging (Low I/P 1f_y) Bit 2: I/P Calibration Shift...
Page 93 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: Bit String 0=inactive 1=active Indicates what caused an Instrument Same as Shutdown.
Page 94 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Bit 0: Travel Limit Hi Hi Bit 1: Travel Limit Lo Lo Bit 2: Travel Limit Hi Bit 3: Travel Limit Lo Bit 7: Travel Open...
Page 95 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: Float AUTO Output Blk Timeout Time >= 0, <= 800 The maximum time between 83.3...
Page 96 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: AUTO Travel Hi Alert Point Alert when valve position is less than 84.12 -25 to 125...
Page 97 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Bit 2: Integrator Limited Bit 3: Integrator Limited High Bit 4: Tvl Sensor Span Error...
Page 98 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category ANSI Seat Leakage Classification 1: I 2: II 3: III 4: IV 5: V...
Page 99 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 102.11 Data Type: UINT16 ACT_SIZE_ENUM These parameters can only reset DEVICE_RECORD through VL/DD.
Page 100 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type:Uint16 This defines MAI_CHANNEL_MAP which transducer block channels will be sent to each of the 8 MAI MAI Channel 1 111.1...
Page 101 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 0: Un-initialized 1: Execute VST (store as reference) 2: Execute VST (store as current)
Page 102 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 125.2 Data Type: UINT8 VST_STEP_NUM 0: None 1: Other 2: Wrong Mode 3: Wrong Position...
Page 103 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category SETUP Data Type: BitStr VST_CRITERIA_CONFIG Bit 2: Break-out Time Bit 3: Travel Time Bit 4: Test Time Bit 6: Outgoing Pressure...
Page 104 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category •0x00 - None •0x01 - User Modified 132.4 •0x02 - PST Jan 1 1972...
Page 105 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category AUTO >=0 Data Type: Float SETUP PST_RANDOM_MAX <=10 Units = % AUTO...
Page 106 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: FFTime 152.3 PST_AUTO_CURRENT_TIME Units = 1/32 msec Data Type: U8 PST_CAL_TRAV Data Type: Float...
Page 107 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category Data Type: Float 161.9 ENTRY_COMPLETE_TIME Units = sec 161.10 Data Type: Float ENTRY_MIN_FRICTION...
Page 108 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 163.12 Data Type: Float ENTRY_MAX_FRICTION VST_HISTORY_3 164.1 2010-Jan-1 -- 2146-Feb-7 Data Type: FFTime ENTRY_TIME...
Page 109 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 166.2 See VST_HISTORY_0 Data Type: UINT8 ENTRY_SOURCE 166.3 See VST_HISTORY_0 Data Type: UINT8...
Page 110 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category •0 - None •1 - Transducer to MAN •2 - Transducer to AUTO •3 - Auto Calibrate 168.2...
Page 111 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category AUTO 170.5 Bit 0: Compression Compression SETUP Data Type: Bit String TRIG_FLAGS AUTO...
Page 112 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category LCP_BUTTON_RECORD 174.1 Jan 1, 1972 Data Type: FFTime LCP_TEST 174.2 Jan 1, 1972...
Page 113 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐12. Transducer Block Parameter Definitions Label Index RO / Protect Mode Range Initial Value Description PARAMETER_NAME Number Category 0: Init 1: Setpoint Latch Engaged 2: Position Latch Engaged Data Type: U8 LATCH_STATE 3: LCP Latch Engaged...
Page 114: View Lists
DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 115 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐13. Transducer Block, View 1 through View 3.5 (continued) View Index Number Parameter PRESSURE_DIFF TVL_PRESS_CONTROL TEMPERATURE DRIVE_SIGNAL DRIVE_CURRENT MLFB INST_ALERTS_ACTIVE SELFTEST_STATUS DEVICE_RECORD BLOCK_INFO TRAVEL_ALWAYS VST_COMMAND VST_MODE VST_PAUSE VST_RESULT...
Page 116 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐14. Transducer Block, View 4.1 through View 4.10 (continued) View Index Number Parameter 4.10 RATED_TRAVEL STOP_HI_POS STOP_LO_POS TRAVEL_UNITS SIGNAL_ACTION ACT_FAIL_ACTION ACT_MAN_ID ACT_MODEL_NUM ACT_SN ACT_TYPE VALVE_MAN_ID VALVE_MODEL_NUM VALVE_SN VALVE_TYPE...
Page 117 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017 Table 4‐14. Transducer Block, View 4.1 through View 4.10 (continued) View Index Number Parameter 4.10 MAI_CHANNEL_MAP OUTBLOCK_SEL VST_SAMPLE_INT VST_ABORT_MODE VST_NORMAL VST_CRITERIA_CONFIG VST_OVERDUE_CONFIG PST_BREAKOUT_TIMEOUT PST_INITIAL_START_TIME PST_INTERVAL PST_OPTIONS PST_RAMP_RATE PST_STRK_TRAV PST_STRK_TRAV_TIMEOUT...
Page 118 DVC6200f Digital Valve Controller Instruction Manual Detailed Setup - Transducer Block D103412X012 February 2017...
Page 119: Section 5 Calibration
DVC6200f Digital Valve Controller Instruction Manual Calibration D103412X012 February 2017 Section 5 Calibration 5-5- Calibration Overview When a DVC6200f digital valve controller is ordered as part of a control valve assembly, the factory mounts the digital valve controller on the actuator and connects the necessary tubing, then sets up and calibrates the controller. For digital valve controllers that are ordered separately, recalibration of the pressure sensors generally is unnecessary.
Page 120: Auto
DVC6200f Digital Valve Controller Instruction Manual Calibration February 2017 D103412X012 If a double‐acting relay is used, you will be prompted to run the relay adjustment when auto or manual calibration is selected. Select Yes to adjust the relay, select No to proceed with calibration. For additional information, refer to Relay Adjustment in this section.
Page 121: Relay
DVC6200f Digital Valve Controller Instruction Manual Calibration D103412X012 February 2017 Relay Follow the prompts on the Field Communicator display to check relay adjustment. Replace the digital valve controller cover when finished. Note Relay B and C are not user‐adjustable. Double‐Acting Relay The double‐acting relay is designated by “Relay A”...
Page 122: Supply Pressure Sensor
DVC6200f Digital Valve Controller Instruction Manual Calibration February 2017 D103412X012 If the low bleed relay option has been ordered stabilization may take approximately two minutes longer than the standard relay. Relay A may also be adjusted for use in single‐acting‐ direct applications. Rotate the adjustment disc as shown in figure 5‐1 for single‐acting direct operation.
Page 123: Pressure A Or B Sensor
DVC6200f Digital Valve Controller Instruction Manual Calibration D103412X012 February 2017 2. The following message appears: Use the Increase and Decrease selections until the displayed pressure matches the instrument supply pressure. Press OK when you have read this message. 3. The value of the pressure appears on the display. 4.
Page 124: Pst Calibration
DVC6200f Digital Valve Controller Instruction Manual Calibration February 2017 D103412X012 5. The instrument sets the output pressure to full supply. The following message appears. Use the Increase and Decrease selections until the displayed pressure matches the output x pressure. Press OK when you have read the message. 6.
Page 125: Section 6 Viewing Device Variables And Diagnostics
DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Section 6 Viewing Device Variables and Diagnostics6-6- View Lists View Lists allow the values of a set of parameters to be accessed at the same time. View lists are available for the resource and transducer blocks, and the function blocks.
Page 126 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Field Diagnostic (FD) Alert Configuration Enable/Suppress the following Field Diagnostic alerts per plant requirements. Refer to Alerts on page 55 for alert specific information. •Electronics •Travel History Drive Current Movement History Drive Signal...
Page 127 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Table 6‐1. Resource Block BLOCK_ERR Conditions Condition Number Condition Name and Description Other ‐ Set if a device initialization error occurred. Block Configuration Error ‐ Set if FEATURE_SEL, CYCLE_SEL, or CYCLE_TYPE is set incorrectly. Simulate Active ‐...
Page 128 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 •Block Alarm: Unacknowledged (BLOCK_ALARM. UNACKNOWLEDGED [36.1]) 1 = Uninitialized 2 = Acknowledged 3 = Unacknowledged Maintenance •Restart Actions (RESTART [16]) WARNING Restarting the instrument may cause loss of process control. To avoid personal injury and property damage caused by the release of pressure of process fluid, isolate the valve from the process and equalize pressure on both sides of the valve or bleed off the process fluid.
Page 129: Device Variables
•Manufacturer (MANUFAC_ID [10]) identifies the manufacturer of the instrument. It is used by the host system to locate the DD file for the device. For Fisher the Manufacturer ID is 0x5100. •Device Type (DEV_TYPE [11]) identifies the type of device. It is used by the host system to locate the DD file for the device.
Page 130 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Options The following parameters are contained in the the Options menu of the resource block. Diagnostic Options (DIAG_OPTIONS [103]) show the diagnostic options available in the instrument. Function Block Options (FB_OPTIONS [102]) show which function blocks are licenced and enabled in the instrument.
Page 131: Transducer Block
DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Transducer Block This section contains information on the DVC6200f digital valve controller transducer block. Descriptions of all transducer block parameters are included. The transducer block decouples function blocks from the local output functions required to command output hardware.
Page 132 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 •Supply Sensor Failure indicates the pressure sensor is reporting a pressure that is significantly outside of the normal operating pressure, and has failed. •IOP Failure indicates the I/O processor has failed. •Drive Current Alert indicates that the Drive Current has exceeded the Drive Current Alert Point for more than the Drive Current Alert Time.
Page 133 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Stroking the Digital Valve Controller Output Stroke Valve is used to confirm proper valve operation. Follow the prompts on the Field Communicator display to select from the following: Done, Ramp Open, Ramp Closed, Ramp to Target, Step to Target, and Stop. •Done—Select this if you are done.
Page 134: Device Variables
DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 •VST State (VST_STATE [125.1]) •VST Result (VST_RESULT [121]) •Test Abnormal Cause (VST_DETAILED_CODE[126]) Device Variables TB > Device Variables Field Communicator TB Block Modes Block Mode: Target (TARGET [5.1]) is the mode requested by the user or host system. Generally, only one mode is allowed to be set, and it must be a permitted mode as defined by the permitted attribute of the mode parameter.
Page 135 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 AO Control - Pre‐Characterization Final Value Setpoint (FINAL_VALUE.VALUE [14.2]) shows the value of the setpoint in % (percent) of ranged travel or pressure. Setpoint is used for both travel and pressure control. This parameter will be written directly if the transducer block is in MAN mode, or will be written automatically by the AO block if the transducer block is in AUTO mode.
Page 136 DVC6200f Digital Valve Controller Instruction Manual Viewing Device Variables and Diagnostics D103412X012 February 2017 Travel Diagnostic Info Drive Signal (DRIVE_SIGNAL [78]) indicates the drive signal, as a percentage of the maximum drive available, going to the I/P converter from the printed wiring board. In most applications, the drive signal ranges between 50% and 75% of the maximum drive signal.
Page 137: Section 7 Maintenance And Troubleshooting
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Section 7 Maintenance and Troubleshooting7-7- The DVC6200f digital valve controller enclosure is rated Type 4X and IP66, therefore periodic cleaning of internal components is not required. If the DVC6200f is installed in an area where the exterior surfaces tend to get heavily coated or layered with industrial or atmospheric contaminants, however, it is recommended that the vent (key 52) be periodically inspected to ensure it is fully open.
Page 138: Replacing The Magnetic Feedback Assembly
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 from fire or explosion if natural gas is used as the supply medium and appropriate preventive measures are not taken. Preventive measures may include, but are not limited to, one or more of the following: ensuring adequate ventilation and the removal of any ignition sources.
Page 139: Component Replacement
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Component Replacement When replacing any of the components of the DVC6200f, the maintenance should be performed in an instrument shop whenever possible. Make sure that the electrical wiring and pneumatic tubing is disconnected prior to disassembling the instrument.
Page 140: Replacing The Module Base
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Figure 7‐1. Printed Wiring Board Cable Connections TERMINAL MODULE BASE ASSEMBLY PRINTED WIRING BOARD ASSEMBLY HOUSING CABLE CABLE TO TRAVEL SENSOR TO TERMINAL BOX W9924‐1 Replacing the Module Base Refer to figure 8‐2 or 8‐4 for key number locations.
Page 141: Submodule Maintenance
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 1. Ensure the module base seal (key 237) is properly installed in the housing (key 1). Ensure the O‐ring (key 12) is in place on the module base assembly. 2.
Page 142 DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Replacing the I/P Filter A screen in the supply port beneath the I/P converter serves as a secondary filter for the supply medium. To replace this filter, perform the following procedure: 1.
Page 143: Printed Wiring Board (Pwb) Assembly
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Figure 7‐4. I/P Converter SHROUD (KEY 169) I/P CONVERTER SOCKET‐HEAD (KEY 41) SCREWS (4) (KEY 23) BOOTS (KEY 210) W9328 3. Install the I/P converter (key 41) straight into the module base (key 2), taking care that the two electrical leads feed into the guides in the module base.
Page 144: Pneumatic Relay
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 2. Properly orient the PWB assembly (key 50) as you install it into the module base. The two electrical leads from the I/P converter (key 41) must guide into their receptacles in the PWB assembly and the pressure sensor bosses on the module base must fit into their receptacles in the PWB assembly.
Page 145: Gauges, Pipe Plugs Or Tire Valves
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 3. Position the relay (with shroud) on the module base. Tighten the four screws, in a crisscross pattern, to a final torque of 2 NSm (20.7 lbfSin). 4. Using the Field Communicator, verify that the value for Relay Type parameter matches the relay type installed. 5.
Page 146: Replacing The Terminal Box
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 4. Disconnect the terminal box wiring connector from the PWB assembly (key 50). 5. Remove the screw (key 72). Pull the terminal box assembly straight out of the housing. Replacing the Terminal Box Note Inspect all O‐rings for wear and replace as necessary.
Page 147: Instrument Troubleshooting
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Instrument Troubleshooting What to Do First When a problem occurs, check the following first: Mounting D Is the feedback linkage connected correctly? See the beginning of this section. Utility Connections D Are pneumatic connections correct? Are there any air leaks? See the Installation section.
Page 148 DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Table 7‐2. Instrument Troubleshooting Symptom Possible Cause Action 1 Instrument will not communicate. 1a No power to device 1a1 Ensure device is connected to the segment (see host system documentation). 1a2 Measure the terminal voltage.
Page 149 DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Table 7‐2. Instrument Troubleshooting Symptom Possible Cause Action 4 Function block actual mode does not 4a Resource block actual mode is Out of Service. 4a Change Resource block target mode to Auto (see change with target mode.
Page 150 DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Table 7‐2. Instrument Troubleshooting Symptom Possible Cause Action 9 Valve does not move when the set 9c Instrument is in fault state. 9c Set Clear FState to Clear (Refer to Fault State on point is changed page 25 of the Detailed Setup / Blocks Section, or host system documentation).
Page 151 DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Table 7‐2. Instrument Troubleshooting Symptom Possible Cause Action 14 Instrument will not calibrate, has 14a Travel sensor failed. 14a Replace the housing (key 1) sluggish performance or oscillates. 14b Travel feedback is out of accepted range 14b Check the mounting.
Page 152: Technical Support Checklist
DVC6200f Digital Valve Controller Instruction Manual Maintenance and Troubleshooting D103412X012 February 2017 Technical Support Checklist Have the following information available prior to contacting your Emerson Automation Solutions sales office support. Reference 1. Instrument serial number as read from nameplate _________________________________________ 2.
Page 153: Section 8 Parts
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should not, under any circumstances, be used in any Fisher instrument. Use of components not supplied by Emerson Automation Solutions may void your warranty, might adversely affect the performance of the instrument, and could cause personal injury and property damage.
Page 154: Parts List
DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Description Part Number Description Part Number 10 Remote Mount Feedback Unit Kit (see figure 8‐5) 13* Gasket/Seal Kit, for use with GX actuator [remote housing assembly (key25); hex socket set [kit contains insulating gasket (key 287) screw (key 58);...
Page 155: Module Base
DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Description Part Number Figure 8‐1. Terminal Box of Natural Gas Certified FIELDVUE DVC6200f Digital Valve Controller I/P Converter Assembly WIRING CONNECTOR (see figure 8‐2 and 8‐4) GAS‐BLOCKING PRESS‐FIT ADAPTOR DVC6200f and DVC6205f (2)(9) 23 Cap Screw, hex socket, SST...
Page 156: Pwb Assembly
DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Description Description Feedback Connections Terminal Box (see figure 8‐4) Pressure Gauges, Pipe Plugs, or Tire Valve Assemblies DVC6205f (see figure 8‐3) 4 Terminal Box Cap (1)(5) 34* O‐ring (1)(5) 36* O‐ring DVC6200f and DVC6205f 58 Set Screw, hex socket, SST...
Page 157 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐2. FIELDVUE DVC6200f Digital Valve Controller Housing Assembly HOUSING B—BACK VIEW HOUSING A—BACK VIEW (USED FOR ALL (USED FOR GX ACTUATOR) ACTUATORS EXCEPT GX) DOUBLE‐ACTING DIRECT‐ACTING REVERSE‐ACTING APPLY LUBRICANT, SEALANT, OR THREAD LOCK APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED GE40185 sheet 1 of 3...
Page 158 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐2. FIELDVUE DVC6200f Digital Valve Controller Housing Assembly (continued) SECTION C-C SCALE 2 : 1 SECTION A-A SECTION E-E SCALE 2 : 1 APPLY LUBRICANT, SEALANT, OR THREAD LOCK SECTION F-F SCALE 2 : 1 APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED...
Page 159 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐4. FIELDVUE DVC6205f Base Unit Housing Assembly SECTION B-B SECTION A-A APPLY LUBRICANT, SEALANT, OR THREAD LOCK SECTION H-H APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED GE40181...
Page 160 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐4. FIELDVUE DVC6205f Base Unit Housing Assembly (continued) SECTION C-C SCALE 2 : 1 SECTION E-E SCALE 2 : 1 DOUBLE‐ACTING SHOWN DOUBLE‐ACTING DIRECT‐ACTING REVERSE‐ACTING APPLY LUBRICANT, SEALANT, OR THREAD LOCK APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED GE40181...
Page 161 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐4. FIELDVUE DVC6205f Base Unit Housing Assembly (continued) PIPE MOUNTING WALL MOUNTING APPLY LUBRICANT, SEALANT, OR THREAD LOCK APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED GE40181...
Page 162 DVC6200f Digital Valve Controller Instruction Manual Parts D103412X012 February 2017 Figure 8‐5. FIELDVUE DVC6215 Remote Feedback Assembly SECTION A-A PARTS NOT SHOWN: 158 APPLY LUBRICANT/SEALANT GE46670-B HOUSING A (USED FOR GX ACTUATOR) SECTION A-A PARTS NOT SHOWN: 158 APPLY LUBRICANT/SEALANT GE40178-B HOUSING B (USED FOR ALL ACTUATORS EXCEPT GX)
Page 163: Appendix A Principle Of Operation
DVC6200f Digital Valve Controller Instruction Manual Principle of Operation D103412X012 February 2016 Appendix A Principle of OperationA‐ A‐ Digital Valve Controller Operation The DVC6200f digital valve controller has a single module base that may be easily replaced in the field without disconnecting field wiring or tubing.
Page 164 DVC6200f Digital Valve Controller Instruction Manual Principle of Operation D103412X012 February 2017 As the setpoint increases, the drive signal to the I/P converter increases, increasing the I/P output pressure. The I/P output pressure is routed to the pneumatic relay submodule. The relay is also connected to supply pressure and amplifies the small pneumatic signal from the I/P converter.
Page 165: Appendix B Field Communicator Menu Tree
DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Appendix B Field Communicator Menu StructureB‐B‐ This section contains the Field Communicator menu trees for the transducer block and the resource block. It also contains Fast Key Sequence tables with coordinates to help locate the function/variable on the appropriate menu tree. Transducer Block (TB) Menu Structure Parameter Label Menu Structure...
Page 166 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Demand Stroke Time Alert Configure/Setup Detailed Setup Alerts Travel History Alerts Stroke History PST Demand Stroke Time Alert Enable >...
Page 167 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure IOP Failure Device Diagnostics Status Self Test Status IOP Failure > > > > Last Calibration Type Configure/Setup Detailed Setup Instrument Calibration Info...
Page 168 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Out of Service Device Diagnostics Status Block Error Out of Service > > > > Outlet Pressure Configure/Setup Detailed Setup Valve and Actuator Valve...
Page 169 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Pressure Fallback FD Config Configure/Setup Detailed Setup Alerts Sensor Alerts Pressure Fallback Pressure Fallback FD Config > > >...
Page 170 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Reset Stroke Time Alert Configure/Setup Detailed Setup Alerts Travel History Alerts Stroke History PST Reset Stroke Time Alert >...
Page 171 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Configure/Setup Detailed Setup FST/PST FST/PST Valve Stroke Test (FST/PST) Test Pause Time > > > > > > Test Pause Time Device Diagnostics PST/FST...
Page 172 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Transducer Block (TB) Menu Structure Parameter Label Menu Structure Travel Open Alert Point Configure/Setup Detailed Setup Alerts Proximity Alerts Travel Open Travel Open Alert Point > > >...
Page 173 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Travel Tuning TRANSDUCER BLOCK Response Control Travel Tuning Set DETAILED SETUP Travel Tuning Travel Proportional Gain Pressure Tuning Travel Velocity Gain Travel/Press Control Travel MLFB Gain Top Level Characterization Travel Integral Enable Custom Characterization Table...
Page 174 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 TRANSDUCER BLOCK DETAILED SETUP > ALERTS Drive Current (continued on next page) Drive Current Drive Current Alert Drive Current Alert Enable Drive Current Shutdown Drive Current Manual Recovery Drive Current Alert Point Drive Current Alert Time Electronic Alerts...
Page 175 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 TRANSDUCER BLOCK DETAILED SETUP > ALERTS Travel Deviation (continued on next page) Travel Deviation Travel Deviation Alert Travel Deviation Alert Enable Travel Deviation Alert Point Travel Deviation Time Travel Alerts Travel Deviation Deadband Travel Deviation FD Config...
Page 176 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 TRANSDUCER BLOCK DETAILED SETUP > ALERTS Performance Critical Alerts Performance Alerts Performance Critical Alert Electronic Alerts Performance Critical Alert Enable PD Inside Status Configuration Alerts Performance Critical FD Config PD Run Sensor Alerts Performance Critical...
Page 177 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 TRANSDUCER BLOCK CALIBRATION Calibration Auto Calibration Top Level PST Calibration Manual Calibration Configure/Setup Configure/Setup Relay Adjust Device Diagnostics Basic Setup Travel Sensor Device Variables Detailed Setup Supply Pressure Calibration Pressure A Pressure B...
Page 178 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Resource Block (RB) Menu Structure Parameter Label Menu Structure Alert Key Configure/Setup Alarm Handling Alert Key > > > Block Alarm: Alarm State Device Diagnostics Block Alarm Block Alarm Alarm State >...
Page 179 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Resource Block (RB) Menu Structure Parameter Label Menu Structure Configure/Setup Identification Manufacturer > > > Manufacturer Device Variables Instrument Identification Manufacturer > > > > Movement History FD Config Device Diagnostics FD Alert Configuration Travel History...
Page 180 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 Resource Block (RB) Menu Structure Parameter Label Menu Structure Write Alarm Auto Acknowledge Configure/Setup Alarm Handling Write Alarm Auto Acknowledge > > > Write Lock Device Diagnostics Write Lock Write Lock >...
Page 181 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 RESOURCE BLOCK DEVICE DIAGNOSTICS Device Diagnostics Active FD Alerts Active FD Alerts FD Alert Configuration -- See below Fail Active Health Index Check Active Recommended Action Offspec Active Resource Block Error Maintenance Active Device State...
Page 182 DVC6200f Digital Valve Controller Instruction Manual Field Communicator Menu Structure D103412X012 February 2017 RESOURCE BLOCK DEVICE VARIABLES Top Level Instrument Configure/Setup Identification Identification Device Diagnostics Version Device Variables Device Variables Device ID Electronics Serial Number Instrument Function Factory Serial Number Options Block Options Field Serial Number...
Page 183: Appendix C Field Diagnostic Alerts
DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Appendix C Field Diagnostic AlertsC‐C‐ Instrument Alert Conditions Instrument Alert Conditions, when enabled, detect many operational and performance issues that may be of interest. To view these alerts, the user must open the appropriate status screen on a host such as a ValveLink software or a DeltaV system.
Page 184: Alert Handling
DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Alert Handling Alert handling is diagrammed in figure C‐1. There are two ways of seeing Field Diagnostic alerts. One way is to see if the instrument alert condition causing the alert is detected. The second is to view alerts reported to the system operator console.
Page 185: Alert Reporting
DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐1. Field Diagnostic Alerts Reporting Requirements Alert Transducer Block Mode (Actual) Drive Current AUTO Drive Signal AUTO Processor Impaired Any Mode Output Block Timeout Any Mode Block Set to Defaults Any Mode Travel Sensor AUTO...
Page 186: Setting Field Diagnostic Alerts
DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Setting Field Diagnostic Alerts Refer to table C‐2 for information on setting alerts. When selected, Field Diagnostic alerts will set the PV status according to table C‐4. Table C‐2. Setting Field Diagnostic Alerts Field Diagnostic Alert Alert Condition Related Parameters...
Page 187 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐2. Setting Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Related Parameters What the Alert is Detecting Guidelines for Setting (Group) (Default) (Default) (Default Alert Category) Double Acting Actuators—...
Page 188 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐2. Setting Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Related Parameters What the Alert is Detecting Guidelines for Setting (Group) (Default) (Default) (Default Alert Category) Use default settings The temperature is greater Temperature High...
Page 189 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐2. Setting Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Related Parameters What the Alert is Detecting Guidelines for Setting (Group) (Default) (Default) (Default Alert Category) Bellows Seal Bonnets—...
Page 190: Using Field Diagnostic Alerts
DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐2. Setting Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Related Parameters What the Alert is Detecting Guidelines for Setting (Group) (Default) (Default) (Default Alert Category) The measured close stroke Stroke close time time is more than the...
Page 191 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐3. Using Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Recommended What the Alert is Detecting Effect on Valve/Instrument Help (Group) (Default) Action (Default Alert Category Check Output Block If the analog or discrete output...
Page 192 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐3. Using Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Recommended What the Alert is Detecting Effect on Valve/Instrument Help (Group) (Default) Action (Default Alert Category) Supply Press Sensor Supply Press The pressure sensor reading is...
Page 193 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐3. Using Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Recommended What the Alert is Detecting Effect on Valve/Instrument Help (Group) (Default) Action (Default Alert Category) Travel Deviation Travel Deviation The Travel Deviation has...
Page 194 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐3. Using Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Recommended What the Alert is Detecting Effect on Valve/Instrument Help (Group) (Default) Action (Default Alert Category) Performance Reduced Performance Reduced performance issues...
Page 195 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐3. Using Field Diagnostic Alerts (continued) Field Diagnostic Alert Alert Condition Recommended What the Alert is Detecting Effect on Valve/Instrument Help (Group) (Default) Action (Default Alert Category) FST Abnormal FST Abnormal If the valve reached the...
Page 196 DVC6200f Digital Valve Controller Instruction Manual Field Diagnostic Alerts February 2017 D103412X012 Table C‐5. Limit Sub Status Out Block Transducer Mode In Cutoff Region Rate Limited Limit Sub‐Status AO, DO Constant AO, DO Constant AUTO High High Limited AUTO Low Limited AUTO High High Limited...
Page 197: Appendix D Foundation Fieldbus Communication
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Appendix D F Fieldbus Communication9‐ OUNDATION D‐D‐ DVC6200f digital valve controllers use Fieldbus to communicate with other fieldbus instruments and OUNDATION the control system. Fieldbus is an all digital, serial, two‐way communication system which interconnects “field” equipment such as transmitters, digital valve controllers, and process controllers.
Page 198: Instrument Specific Blocks
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Figure D‐1 illustrates the internal structure of a function block. When execution begins, input parameter values from other blocks are snapped‐in by the block. The input snap process ensures that these values do not change during the block execution.
Page 199: Block Modes
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Block Modes All blocks have modes. The mode determines the source of the set point, the destination of the output, how the block executes, and the relationship between setpoint and output. The block mode is determined by the Block Mode parameter.
Page 200: Explanation Of Modes
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Note A downstream block changing to Out of Service impacts the mode of the upstream block. Refer to the block hierarchy in figure D‐2. Figure D‐2. Digital Valve Controller Block Hierarchy Example RESOURCE BLOCK ANALOG OUTPUT TRANSDUCER...
Page 201: Examples Of Modes For Various Operation Statuses
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Remote Output (ROut)—The block outputs are set to the value of the remote output parameter that is written by a host computer or others. To prevent a sudden change in output, the block's calculations are initialized when a change in mode occurs.
Page 202: Status Propagation
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Table D‐3. Status Attribute Quality and Substatus Components Quality Substatus Good (NC) Non‐specific Good (NC) Active Block Alarm Good (NC) Active Advisory Alarm Good (NC) Active Critical Alarm Good (NC) Unack Block Alarm Good (NC)
Page 203: Network Communication
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 AO Block D If the valve position is below the low cutoff value, the AO block READBACK status limit is LOW_LIMITED. D If the valve position is above the high cutoff value, the AO block READBACK status limit is HIGH_LIMITED. D If the transducer block actual mode is Auto and the above conditions are not true, the AO block READBACK status limit is NOT_LIMITED.
Page 204: Device Communications
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 D recognizes and adds new devices to the link. D removes non‐responsive devices from the link. D distributes Data Link (DL) and Link Scheduling (LS) time on the link. Data Link Time is a network‐wide time periodically distributed by the LAS to synchronize all device clocks on the bus.
Page 205: Unscheduled Transfers
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 Figure D‐4. Scheduled Data Transfer Host System Schedule DT(A) CD (X, A) LAS=Link Active Scheduler P=Publisher Device X Device Y Device Z S=Subscriber CD=Compel Data DT=Data Transfer Packet B2713‐1 Unscheduled Transfers Figure D‐5 diagrams an unscheduled transfer.
Page 206: Function Block Scheduling
DVC6200f Digital Valve Controller Instruction Manual Fieldbus Communication OUNDATION February 2017 D103412X012 D Report Distribution: This type of communication is used to broadcast and multicast event and trend reports. D Client/Server: This type of communication is used for request/ response exchanges between pairs of devices, such as a set point change.
Page 207: Appendix E Function Blocks
DVC6200f Digital Valve Controller Instruction Manual Function Blocks February 2017 D103412X012 Appendix E Function Blocks 10‐E‐ Analog Output Function Block ....Proportional/Integral/Derivative Function Block ......Control Selector Function Block .
Page 208 DVC6200f Digital Valve Controller Function Blocks Instruction Manual February 2017 D103412X012...
Page 209: Analog Output Function Block
DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Analog Output Function BlockE‐ Overview The Analog Output (AO) function block (figure E‐1) assigns an output value to a field device through a specified I/O channel. The block supports mode control, signal status calculation, and simulation. Figure E‐1 illustrates the internal components of the AO function block, and table E‐2 lists the definitions of the block parameters.
Page 210 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Figure E‐2. Analog Output Function Block Schematic RCAS OUT RCAS IN BKCAL OUT READ BACK SP RATE DN SP RATE UP Operator Setpoint Convert and Status HI/LO Rate Calculation CAS IN Limit Limit SP WRK SP LOW LIM PV SCALE SP HI LIM IO OPTS MODE Shed...
Page 211 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 D Out of Service (OOS)—The block is not processed. The output channel is maintained at the last value and the status of OUT [9] is set to Bad: Out of Service. The BLOCK_ERR [6] attribute shows Out of Service. D Initialization Manual (Iman)—The path to the output hardware is broken and the AO block output will remain at the last position.
Page 212 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 For any shed with no return option, the target mode changes as determined by the option. Therefore, there is no attempt to restore the connection following failure. The behavior on change to the remote cascade target mode is identical to that for Shed With Return Options.
Page 213 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 To select the manner of processing the SP and the channel output value configure the setpoint limiting options, the tracking options, and the conversion and status calculations. Output Block PV Status The Output Block PV Status is determined by the value of the Field Diagnostic Alerts Set PV Status parameter in the transducer block (FD_OPTIONS, bit 1 [96]), the Transducer Block mode, and enabled Active Field Diagnostic alarms.
Page 214 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Figure E‐3. Analog Output Function Block Timing Diagram CAS_IN, 2 1 macrocycle SP RATE DN 1 macrocycle SP RATE UP TRANSDUCER BLOCK TRAVEL TARGET 1 second 1 second 1 second 1 second B2718‐1 Time Action On Fault Detection...
Page 215 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Use Fault State value on Restart—Use the value of FSTATE_VAL [24] for SP [8] when power is restored or if the device is restarted, otherwise use the last value saved in non‐volatile memory. This does not act like Fault State, it only uses the value of FSTATE_VAL [24].
Page 216 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Block Errors Table E‐1 lists conditions reported in the BLOCK_ERR [6] parameter. Table E‐1. AO BLOCK_ERR Conditions Condition Number Condition Name and Description Block Configuration Error ‐ CHANNEL and SHED_OPT set to 0 Simulate active ‐...
Page 217 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Table E‐2. Analog Output Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Block Mode MODE_BLK OOS until Data Type: DS‐69 block is Valid Bits: 7: OOS, 6: IMAN, 5: LO, 4: MAN, 3: AUTO, TARGET...
Page 218 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Table E‐2. Analog Output Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Grant Deny Data Type: DS‐70 GRANT_DENY Options for controlling access of host computers and local control panels to operating, tuning, and 0: Program GRANT...
Page 219 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Table E‐2. Analog Output Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Data Type: Float Preset value to use if I/O_OPTS Fault State Value Fault State to Value or Use Fault State Value on PV Scale +/- 10%...
Page 220 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Table E‐2. Analog Output Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode SUBCODE 30.4 VALUE 30.5 Extended Parameters Data Type: Float StdDev Standard Deviation.
Page 221 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017 Field Communicator Menu Structure ANALOG OUTPUT FUNCTION BLOCK Quick Config Online Alert Key Characteristics Block Tag Back Calculation Output Status Process Value Scale EU at 100% Static Revision Back Calculation Output Value Process Value Scale EU at 0% Tag Description...
Page 222 DVC6200f Digital Valve Controller Instruction Manual AO Function Block D103412X012 February 2017...
Page 223: Function Block
DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 PID Function Block Overview The PID function block (figure E‐4) combines all of the necessary logic to perform proportional/integral/derivative (PID) control. The block supports mode control, signal scaling and limiting, feedforward control, override tracking, alarm limit detection, and signal status propagation.
Page 224 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 α: fixed smoothing factor of 0.1 applied to RATE feedforward control contribution from the feedforward input (FF_VAL) error between setpoint and process variable To further customize the block for use in your application, you can configure filtering, feedforward inputs, tracking inputs, setpoint and output limiting, PID equation structures, and block output action.
Page 225 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Modes The PID function block supports the following modes: D Manual (Man)—The block output (OUT [9]) may be set manually. D Automatic (Auto)—The SP [8] may be set manually and the block algorithm calculates OUT [9]. D Cascade (Cas)—The SP [8] is calculated in another block and is provided to the PID block through the CAS_IN [18] connection.
Page 226 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Shed With No Return Options For any shed with no return option, the target mode changes as determined by the option. Therefore, there is no attempt to restore the connection following failure. The behavior on change to a remote target mode is identical to that for Shed With Return Options.
Page 227 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 In Manual mode the output is entered manually by the operator. In Remote Output mode, the output is entered by a host computer. Output Selection and Limiting Output selection is determined by the mode and the set point. In Automatic, Cascade, or Remote Cascade mode, the output is computed by the PID control equation.
Page 228 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 D Act On IR—If this option is true, then when IR (Initialization Requested) is received on BKCAL_IN [27], the SP [8] will be adjusted within setpoint limits to provide bumpless transfer when the cascade is closed. If the setpoint required to provide bumpless transfer is outside the setpoint limits, then any difference added to provide bumpless transfer will be removed in the BAL_TIME [25].
Page 229 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Process alarm detection is based on the PV [7] value. You can configure the alarm limits of the following standard alarms: D High (HI_LIM [51]) D High high (HI_HI_LIM [49]) D Low (LO_LIM [53]) D Low low (LO_LO_LIM [55]) Additional process alarm detection is based on the difference between SP [8] and PV [7] values and can be configured...
Page 230 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Block Errors Table E‐5 lists conditions reported in the BLOCK_ERR [6] parameter. Table E‐5. PID BLOCK_ERR Conditions Condition Number Condition Name and Description Block Configuration Error—SHED_OPT or BYPASS set to 0 Local Override—The actual mode is LO and Track Enable is set.
Page 231 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Process Value Data Type: DS‐65 Dynamic The process variable used in block execution. Data Type: DS‐65 The target block setpoint value.
Page 232 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Data Type: Float Setpoint Rate Down Ramp rate for downward SP changes. When the Positive + INF SP_RATE_DN...
Page 233 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode 0=Invalid 1=Normal Shed, Normal Return 2=Normal Shed, No Return 3=Shed to Auto, normal return Data Type: Uint8...
Page 234 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Update Event UPDATE_EVT 0=Undefined UNACKNOWLEDGED 43.1 1=Acknowledged Unacknowledged Data Type: DS‐73 0=Undefined This alert is generated by any changes to the static...
Page 235 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Data Type: Float Low Low Limit PV_SCALE, or -INF -INF The setting for the alarm limit used to detect the LO_LO_LIM...
Page 236 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Low Low Alarm LO_LO_ALM 0=Undefined UNACKNOWLEDGED 63.1 1=Acknowledged 0=undefined Unacknowledged Data Type: DS‐71...
Page 237 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode 0=PID terms on error 1=PI terms on error, D term on PV 2=I terms on error, PD term on PV...
Page 238 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐6. PID Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode T Ipgain Data Type: Float T_IPGAIN Integrated process gain. T Ugain Data Type: Float T_UGAIN...
Page 239 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 240 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Table E‐7. PID Function Block, View Lists View Index Number Parameter TRK_VAL FF_VAL FF_SCALE FF_GAIN ALARM_SUM ACK_OPTION ALARM_HYS HI_HI_PRI HI_HI_LIM HI_PRI HI_LIM LO_PRI LO_LIM LO_LO_PRI LO_LO_LIM DV_HI_PRI DV_HI_LIM DV_LO_PRI DV_LO_LIM BIAS...
Page 241 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 Field Communicator Menu Structure PID FUNCTION BLOCK Advanced Config Online Quick Config Back Calculation Hysteresis Back Calculation Input Status Alert Key Feed Forward Gain Back Calculation Input Value Control Options Feed Forward Scale EU at 100% Back Calculation Output Status...
Page 242 DVC6200f Digital Valve Controller Instruction Manual PID Function Block D103412X012 February 2017 All (continued) All (continued) PID FUNCTION BLOCK cont. Other Characteristics Block Tag Updated Event Unacknowledged T Ipgain Other (continued) Static Revision Update Event Update State T Ugain Tag Description Update Event Time Stamp T Uperiod Tag Description...
Page 243: Control Selector Function Block
DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Control Selector Function Block The Control Selector (CSEL) function block (figure 8‐6) selects one of three control signals to perform override control to a PID function block. The block supports mode control. The outputs are calculated based on the actual operation mode, which is determined by parameter values and input value statuses.
Page 244 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 The diagram in figure E‐7 shows the internal components of the Control Selector function block: Figure E‐7. Control Selector Function Block Schematic Diagram OUT_HI_LIM SEL_TYPE OUT_LO_LIM SEL_1 Output Signal SEL_2 Limiting...
Page 245 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Output Limit Scaling During download OUT_HI_LIM and OUT_LO_LIM are set to their configured values. If you have not changed these values from their defaults they are set as follows during the first execution of the block: D OUT_HI_LIM is set to OUT_SCALE(EU100) D OUT_LO_LIM is set to OUT_SCALE(EU0) During runtime the limits are restricted as follows:...
Page 246 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Automatic Mode OUT status is set to Good: Cascade. The limit status of the selected input (SEL_1, SEL_2 or SEL_3) is also copied to OUT. The status and value of the BKCAL_SEL_1, BKCAL_SEL_2 or BKCAL_SEL_3 parameter corresponding to the selected input is set equal to the OUT status and value.
Page 247 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Application Information The Control Selector function block is ideal for providing automatic override control. This function block can take three control signals as input. The user can select SEL_TYPE = Low, Medium, or High for various control configurations. Figure E‐8.
Page 248 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Figure E‐9. FLC block Connected to a Control Selector Block Function Block BKCAL_OUT BKCAL_IN Flow Controller Function Block Function CAS_IN SEL_1 Block Control Selector Function Pressure Controller SEL_2 Block Function Block...
Page 249 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Figure E‐10. Flow control with pressure override Flow Pressure CTLSL SEL_1 OUT SEL_2 Supply Valve NOTE: IN THIS EXAMPLE, BOTH THE FLOW AND PRESSURE PID BLOCKS CONTROL A SUPPLY VALVE. THE FLOW PID OPERATES IN A PRESSURE REGIME BELOW A SAFETY LIMIT.
Page 250 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Control Selector Function Block Parameters D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐9.
Page 251 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Table E‐9. Control Selector Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Output Scale OUT_SCALE Data Type: DS‐68 EU_100 The high and low scale values, engineering units EU_0 code, and number of digits to the right of the...
Page 252 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Table E‐9. Control Selector Function Block System Parameters Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Data Type: DS‐65 BKCAL_SEL_1 The selector output value associated with SEL_1 for backward output tracking.
Page 253 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 254 DVC6200f Digital Valve Controller Instruction Manual CSEL Function Block D103412X012 February 2017 Field Communicator Menu Structure CONTROL SELECTOR FUNCTION BLOCK Characteristics Block Tag Static Revision Tag Description Strategy Alert Key Block Mode Target Block Mode Actual Block Mode Permitted Block Mode Normal Block Error Outpoint Status Outpoint Value...
Page 255: Input Selector Function Block
DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 Input Selector Function Block Overview The Input Selector (ISEL) function block (figure E‐11) can be used to select the first good, maximum, minimum, average, or hot backup from as many as eight input values and place it at the output. The block supports signal status propagation.
Page 256 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 D The Input Selector block Target mode is Auto, OP_SELECT [22] is not being used, and SELECT_TYPE [19] is 0. In this case, the BLOCK_ERR [6] parameter shows a Block Configuration Error. The Input Selector block Actual mode will be Manual if all of the above is not true and the Target mode is Manual.
Page 257 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 When the block is in the Manual mode the status and substatus of OUT [7] and SELECTED [21] will be as follows: D Substatus will be non‐specific and the limit will be constant. D Quality of OUT [7] and SELECTED [21] will be Uncertain if STATUS_OPTS [10] is “Uncertain if in Manual mode.”...
Page 258 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 Figure E‐13. Input Selector Block Limit Propagation START Propagate OP_SELECT selected input equal to zero? limit status All inputs with SELECT_TYPE same limit Average? status? Propagate Not Limited Propagate that All inputs with limit status...
Page 259 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 Figure E‐14. Input Selector Block Substatus Propagation START Propagate Bad, MODE_BLK Out of Service OOS? STATUS_OPTS Un Propagate MODE_BLK certain if Man Uncertain MAN? Mode? Propagate Good Noncascade MODE_BLK must be Auto Propagate Bad,...
Page 260 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 STATUS_OPTS Supported In the STATUS_OPTS [10] parameter, you can select from the following options to control the status handling: D Use Uncertain as Good—sets the OUT [7] status to Good when the selected input status is Uncertain. D Uncertain if in Manual mode: sets the OUT [7] status to Uncertain when the mode is Manual.
Page 261 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 IN_1 through IN_8 and DISABLE_1 through DISABLE_8 are non‐volatile type parameters so if they are Linked they will automatically have Bad status until connections are re‐established. If they are not Linked, they will be restored with the previous value from NVM across device restarts.
Page 262 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 Alarms are grouped into five levels of priority, as shown in table E‐11. Table E‐11. ISEL Function Block Alarm Priorities Priority Number Priority Description The priority of an alarm condition changes to 0 after the condition that caused the alarm is corrected. An alarm condition with a priority of 1 can be recognized by the system.
Page 263 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 ISEL Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentations and shared Index Numbers indicate sub‐parameters Table E‐13.
Page 264 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 Table E‐13. Input Selector Function Block Parameter Definitions Label Index Block RO / RW Range Initial Value Description PARAMETER_NAME Number Mode Status Not Connected Input 1 Data Type: DS‐65 constant IN_1 The block input value and status.
Page 265 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 Table E‐13. Input Selector Function Block Parameter Definitions Label Index Block RO / RW Range Initial Value Description PARAMETER_NAME Number Mode Update Event UPDATE_EVT 0=Undefined UNACKNOWLEDGED 23.1 1=Acknowledged 2=Unacknowledged Data Type: DS‐73 0=Undefined...
Page 266 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 Table E‐13. Input Selector Function Block Parameter Definitions Label Index Block RO / RW Range Initial Value Description PARAMETER_NAME Number Mode Value Not Connected Data Type: DS‐66 constant Disable Analog Input 7 Enable/Disable for Input_7, If parameter is TRUE DISABLE_7...
Page 267 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 Table E‐13. Input Selector Function Block Parameter Definitions Label Index Block RO / RW Range Initial Value Description PARAMETER_NAME Number Mode High Alarm HI_ALM 0=Undefined UNACKNOWLEDGED 46.1 1=Acknowledged Unacknowledged 0=Undefined Data Type: DS‐71...
Page 268 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 269 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block D103412X012 February 2017 Field Communicator Menu Structure INPUT SELECTOR FUNCTION BLOCK Quick Config Online Other continued All continued High High Priority Alert Key Select Type Block Error High High Limit Min Good Min Good Disable Analog Input 1 Status High Priority...
Page 270 DVC6200f Digital Valve Controller Instruction Manual ISEL Function Block February 2017 D103412X012...
Page 271: Output Splitter Function Block
DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 Output Splitter Function Block262. Overview The Output Splitter (OS) block (figure E‐15) provides the capability to drive two control outputs from a single input. Each output is a linear function of some portion of the input. Back calculation support is provided using the same linear function in reverse.
Page 272 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 Figure E‐16. Output Splitter Function Block Schematic IN_ARRAY OUT_ARRAY LOCKVAL RCAS_IN CAS_IN Auto BKCAL_IN_1 RCAS_OUT BKCAL_IN_2 CAS_OUT Figure E‐17. Output Splitter Function Block Schematic Diagram Setpoint SP_WRK Setpoint "...
Page 273 DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 D Out of Service (OOS)—The block is not processed. FIELD_VAL and PV are not updated and the OUT status is set to Bad: Out of Service. The BLOCK_ERR parameter shows Out of Service. In this mode, you can make changes to all configured parameters.
Page 274 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 Limit Handling The splitter function block is designed to combine the limit information from the two downstream blocks into limits for the upstream block. The general principle is to allow the upstream block to continue control for as long as possible. The upstream block is high‐limited (BKCAL_OUT of the Splitter block has high‐limited status) when: D Both downstream blocks are high‐limited (both BKCAL_INS of the Splitter block have high‐limited status) D One downstream block is high‐limited, the associated output slope is positive, and the other block has Bad status or...
Page 275 DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 blocks may effect the useful range of a line. Units of percent are used in the examples because the common application of this block is to valves, but any units may be used to suit the application. Figure E‐18.
Page 276 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 to OUT_2, or goes to Y . If LOCKVAL is true, OUT_1 remains at its ending value when X is greater than X . If LOCKVAL is false, then OUT_1 goes to Y when X is greater than X Figure E‐17.
Page 277 DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 CAS_IN of the Splitter receives the OUT of PID1. BKCAL_IN of PID1 receives BKCAL_OUT of the Splitter. CAS_IN of the AO receives OUT_1 of the Splitter and PID2 receives OUT_2 of the Splitter. BKCAL_IN_1 of the Splitter receives BKCAL_OUT of the AO and BKCAL_IN_2 of the Splitter receives BKCAL_OUT of PID2.
Page 278 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 drop the good downstream block out of Cas mode for one evaluation cycle and then restore Cas mode. This initializes the upstream controller to the remaining good region of control. Block Errors Table E‐19 lists conditions reported in the BLOCK_ERR [6] parameter.
Page 279 DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 266. OS Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐20.
Page 280 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 Table E‐20. Output Splitter Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Data Type: DS‐68 EU at 100% The high and low scale values, engineering units code, Output 2 Range EU at 0 % and number of decimal places to be used in displaying...
Page 281 DVC6200f Digital Valve Controller Instruction Manual OS Function Block D103412X012 February 2017 Table E‐20. Output Splitter Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Block Alarm BLOCK_ALM 0: Undefined UNACKNOWLEDGED 24.1 1: Acknowledged 2: Unacknowledged 0: Undefined Data Type: DS‐72...
Page 282 DVC6200f Digital Valve Controller Instruction Manual OS Function Block February 2017 D103412X012 Field Communicator Menu Structure OUTPUT SPLITTER FUNCTION BLOCK Characteristics Block Tag Static Revision Tag Description Strategy Alert Key Block Mode Target Block Mode Actual Block Mode Permitted Block Mode Normal Block Error Setpoint Status Setpoint Value...
Page 283: Analog Input Function Block
DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Analog Input Function Block Overview The Analog Input (AI) function block (figure E‐21) processes field device measurements and makes them available to other function blocks. The output value from the AI block is in engineering units and contains a status indicating the quality of the measurement.
Page 284 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Figure E‐22. Analog Input Function Block Schematic ANALOG MEASUREMENT ALARM_TYPE ACCESS HI_HI_LIM ANALOG HI_LIM MEAS. ALARM LO_LO_LIM DETECTION LO_LIM OUT_D CHANNEL ALARM_HYS LOW_CUT CUTOFF FILTER CONVERT STATUS CALC. SIMULATE L_TYPE PV_FTIME...
Page 285 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Table E‐23. Channel Selections for the Analog Input Function Block Channel Parameter Block Index Number XD_SCALE Units WORKING_SP % (1342) FINAL_POSITION_VALUE % (1342) WORKING_POS % (1342) SUPPLY_PRESSURE psig (1143), bar (1137), kPa (1133), inHg (1155), inH20 (1146), kg/cm2 (1145) PRESSURE_A psig (1143), bar (1137), kPa (1133), inHg (1155), inH20 (1146), kg/cm2 (1145) PRESSURE_B...
Page 286 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Filtering The filtering feature changes the response time of the device to smooth variations in output readings caused by rapid changes in input. You can adjust the filter time constant (in seconds) using the PV_FTIME [18] parameter. Set the filter time constant to zero to disable the filter feature.
Page 287 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 When the converted input value is below the limit specified by the LOW_CUT [17] parameter, a value of zero is used for the converted value (PV [7]). This option is useful to eliminate false readings when the differential pressure measurement is close to zero.
Page 288 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Troubleshooting Refer to table E‐25 to troubleshoot any problem that you encounter. Table E‐25. Troubleshooting Symptom Possible Causes Corrective Action Mode will not leave OOS Target mode is not set Set target mode to something other than OOS BLOCK_ERR [6] will show the configuration error bit set.
Page 289 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 AI Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐26.
Page 290 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Table E‐26. Analog Input Block Parameter Definitions Label Index RO / Write Block Initial Range Description PARAMETER_NAME Number Mode Value Data Type: DS‐68 EU at 100% The high and low scale values, engineering units Output Scale EU at 10% code, and number of decimal places to be used in...
Page 291 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Table E‐26. Analog Input Block Parameter Definitions Label Index RO / Write Block Initial Range Description PARAMETER_NAME Number Mode Value Block Alarm BLOCK_ALM Undefined UNACKNOWLEDGED 21.1 Acknowledged Unacknowledged Data Type: DS‐72 Undefined The block alarm is used for all configuration,...
Page 292 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Table E‐26. Analog Input Block Parameter Definitions Label Index RO / Write Block Initial Range Description PARAMETER_NAME Number Mode Value Low Alarm LO_ALM UNACKNOWLEDGED 35.1 Data Type: DS‐71 ALARM_STATE 35.2 The status of the lo alarm and its associated time...
Page 293 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 294 DVC6200f Digital Valve Controllers Instruction Manual AI Function Block D103412X012 February 2017 Field Communicator Menu Structure ANALOG INPUT FUNCTION BLOCK Quick Config Online All (continued) AI Channel Block Error Characteristics Block Tag Alarm Hysteresis Linearization Type Field Value Status Static Revision High High Priority Transducer Scale EU at 100% Field Value Value...
Page 295: Mulitple Analog Input Function Block
DVC6200f Digital Valve Controller Instruction Manual MAI Function Block D103412X012 February 2017 Multiple Analog Input Function Block Overview The Multiple Analog Input (MAI) function block (figure E‐24) has the ability to process up to eight field device measurements and make them available to other function blocks. The output values from the MAI block are in engineering units and contain a status indicating the quality of the measurement.
Page 296 DVC6200f Digital Valve Controller Instruction Manual MAI Function Block February 2017 D103412X012 OUT_X status will be Bad if the transducer detects a problem with sensor associated with the channel. Application Information The intended use is for applications where it is necessary to convey DVC6200f measurements from a function. The configuration of the MAI function block and its associated output channels depends on the specific application.
Page 297 DVC6200f Digital Valve Controller Instruction Manual MAI Function Block D103412X012 February 2017 MAI Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐30.
Page 298 DVC6200f Digital Valve Controller Instruction Manual MAI Function Block February 2017 D103412X012 Table E‐30. MAI Function Block Parameter Definitions Label Index RO / Mode Range Initial Value Description Parameter Name Number Output 1 Channel assigned by Data Type: DS‐65 TB.DRIVE_SIGNAL OUT_1 TB.MAI_CHANNEL_MAP The block output value and status.
Page 299 DVC6200f Digital Valve Controller Instruction Manual MAI Function Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 300 DVC6200f Digital Valve Controller Instruction Manual MAI Function Block February 2017 D103412X012 Field Communicator Menu Structure MULTIPLE ANALOG INPUT FUNCTION BLOCK Quick Config Online Alert Key Block Error Characteristics Block Tag Block Mode Target Static Revision Block Mode Actual Tag Description Common Config Block Mode Permitted Strategy...
Page 301: Discrete Output Function Block
DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Discrete Output Function Block Overview The Discrete Output (DO) function block (figure E‐25) processes a discrete set point and outputs it to the specified I/O channel to produce an output signal. The DVC6200f digital valve controller discrete output block provides both normal open/closed control and the ability to position the valve in 5% increments for coarse throttling applications.
Page 302 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 Figure E‐26. Discrete Output Function Block Schematic RCAS_OUT_D RCAS_IN_D BKCAL_OUT_D PV_D SP_D CONVERT AND STATUS CAS_IN_D OUT_D CALCULATION READBACK_D IO_OPTS MODE SIMULATE_D SHED MODE CHANNEL TRANSDUCER TRANSDUCER BLOCK FEEDBACK BLOCK Modes The DO block supports the following modes:...
Page 303 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Mode Handling Shed Options — RCAS Mode Only Shed from or climb to a remote mode is determined by the parameter SHED_OPT [23]. A block climbs and sheds through the same path.
Page 304 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 Block Initialization The Fieldbus Foundation specification requires that certain parameters have initial values of uninitialized in function blocks. In addition to setting the Resource block mode to AUTO, the control system or the user must change those parameters from their uninitialized value to a valid value in order for the function block to move from the Out of Service mode.
Page 305 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Table E‐33. Valve Set Point for Discrete State Discrete State Valve Set Point with IO_OPTS Invert = 0 Valve Set Point with IO_OPTS Invert = 1 Closed Open Open Closed Closed...
Page 306 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 Block Errors Table E‐34 lists conditions reported in the BLOCK_ERR [6] parameter. Table E‐34. DO BLOCK_ERR Conditions Condition Number Condition Name and Description Block Configuration Error ‐ SHED_OPT or CHANNEL set to 0 (uninitialized) Simulate active ‐...
Page 307 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Simulation To support testing of the control strategy, you can enable the SIMULATE_D [17] parameter. Normally, the valve position value and status used for READBACK_D [16] in the DO block reflect actual process values to the nearest 5%, as provided by the transducer block.
Page 308 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 DO Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐35.
Page 309 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Table E‐35. Discrete Output Function Block Parameter Definitions Label Index RO / Mode Range Initial Value Description PARAMETER_NAME Number Simulate Discrete SIMULATE_D SIMULATE_STATUS 10.1 Not Specific Not Limited Data Type: DS‐83 Allows the transducer discrete input or output SIMULATE_VALUE...
Page 310 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 Table E‐35. Discrete Output Function Block Parameter Definitions Label Index RO / Mode Range Initial Value Description PARAMETER_NAME Number Data Type: Float Fault State Time Time from detection of a fault in the remote set Positive FSTATE_TIME point to the Fault State output action.
Page 311 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Table E‐35. Discrete Output Function Block Parameter Definitions Label Index RO / Mode Range Initial Value Description PARAMETER_NAME Number Block Alarm BLOCK_ALM Data Type: DS‐72 0=Undefined The block alarm is used for all configuration, UNACKNOWLEDGED 26.1 1=Acknowledged...
Page 312 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 313 DVC6200f Digital Valve Controller Instruction Manual DO Function Block D103412X012 February 2017 Field Communicator Menu Structure DISCRETE OUTPUT FUNCTION BLOCK Quick Config Online Alert Key Back Calculation Output Discrete Status Characteristics Block Tag Process Value Discrete Status Back Calculation Output Discrete Value Static Revision Process Value Discrete Value Block Error...
Page 314 DVC6200f Digital Valve Controller Instruction Manual DO Function Block February 2017 D103412X012...
Page 315: Discrete Input Function Block
DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Discrete Input Function Block Overview The Discrete Input (DI) function block (figure E‐27) processes a single discrete input from a field device and makes it available to other function blocks. You can configure inversion and alarm detection on the input value. In the DVC6200f digital valve controller, the discrete input function block can provide limit switch functionality and valve position proximity detection.
Page 316 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Modes The Discrete Input function block supports the following modes: D Manual (Man)—The block output (OUT_D [8]) is disconnected from the field and set manually. D Automatic (Auto)—The block algorithm determines output. D Out of Service (OOS)—The block is not processed.
Page 317 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Table E‐37. Channel Selection for the Discrete Input Function Block Selection Transducer Block Parameter Transducer Block Index Number Bit Number TRAVEL_D INST_ALERTS_ACTIVE:GROUP_2_ACTIVE 81.2 7: Travel Open INST_ALERTS_ACTIVE:GROUP_2_ACTIVE 81.2 8: Travel Closed INST_ALERTS_ACTIVE:GROUP_2_ACTIVE 81.2...
Page 318 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 the detected position. Figure E‐29 illustrates the operation of the proximity detection function. Travel Alert Point refers to Travel Lo Alert Point, Travel Hi Alert Point, Travel Lo Lo Alert Point, and Travel Hi Hi Alert Point in table E‐39. Travel Alert Deadband refers to Travel Lo Alert Deadband, Travel Hi Alert Deadband, Travel Lo Lo Alert Deadband, and Travel Hi Hi Alert Deadband in table E‐39.
Page 319 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Alarm Detection To select the state that initiates an input alarm, and to set discrete alarm substatus in the output, configure the DISC_LIM [23] parameter. You can enter any value between 0 and 255. A value of 255 disables the alarm. When OUT_D [8] matches the DISC_LIM [23] state, the discrete value of an alarm is set.
Page 320 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Figure E‐30. Proximity Discrete Input Compared to a Standard Discrete Input STANDARD DISCRETE INPUT DISCRETE INPUT VALUE DISCRETE PROXIMITY DISCRETE INPUT INPUT VALUE Configurable Band With the proximity discrete input a configurable band can be established about a central point. Whenever the valve position enters this configurable band, the discrete input changes state.
Page 321 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 DI Function Block Parameter List D Read/Write Capability: RO - Read Only, RW - Read Write D Mode: The block mode(s) required to write to the parameter D Double indentation and shared Index Number indicates sub‐parameter Table E‐41.
Page 322 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Table E‐41. Discrete Input Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Simulate Discrete SIMULATE_D Data Type: DS‐83 SIMULATE_STATUS Allows the transducer discrete input or output SIMULATE_VALUE to the block to be manually supplied when TRANSDUCER_STATUS...
Page 323 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Table E‐41. Discrete Input Function Block Parameter Definitions Label Index RO / Block Range Initial Value Description PARAMETER_NAME Number Mode Update Event UPDATE_EVT 0=Undefined UNACKNOWLEDGED 18.1 1=Acknowledged 0=Undefined 2=Unacknowledged Data Type: DS‐73 0=Undefined...
Page 324 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 View Lists View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains static parameters with configuration and maintenance information.
Page 325 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017 Field Communicator Menu Structure DISCRETE INPUT FUNCTION BLOCK Quick Config Online Alert Key Block Error Characteristics Block Tag Process Value Discrete Status Field Value Discrete Status Static Revision Process Value Discrete Value Field Value Discrete Value Tag Description...
Page 326 DVC6200f Digital Valve Controller Instruction Manual DI Function Block D103412X012 February 2017...
Page 327: Appendix F Device Description Installation
6‐digit hexadecimal equivalent of the manufacturer's identification number as defined by the Fieldbus Foundation. Fisher Controls' ID number is 5100 (or in the folder format 005100). This number is also stored in the instrument Resource Block in the parameter Mfg ID (parameter name MANUFAC_ID).
Page 328: Device Descriptions And Methods
DVC6200f Digital Valve Controller Instruction Manual Device Description Installation D103412X012 February 2017 D .ffo—This extension denotes a complete, tokenized, device description for the instrument as defined by the Fieldbus Foundation. D .cff—This extension denotes a capabilities file for the instrument as defined by the Fieldbus OUNDATION Common File Format specification.
Page 329 Be sure to select the correct DD for the DeltaV revision being used. The resource files are different for each revision of DeltaV. D Device descriptions furnished by Fisher contain only those files applicable to Fisher. All the files are located in the manufacturer ID Folder (005100 for xxxxxx in directory structure above).
Page 330: Installing Dds On Other Fieldbus Host Systems
It is placed on the media starting with the release folder, which then contains a folder (xxxxxx) for each manufacturer as defined above. For Fisher this folder is 005100. A readme file may be included at the top level. Read this file for any additional information regarding the DD.
Page 331: Displaying The Device Description Revision
DVC6200f Digital Valve Controller Instruction Manual Device Description Installation D103412X012 February 2017 up the DD on your system. Note the folder where the decompressed files are placed. This information will be required later in the installation procedure. Note This procedure will install the necessary Device Description files (*.ffo and *.sym), and Capabilities file (*.cff) for the device. 1.
Page 332 DVC6200f Digital Valve Controller Instruction Manual Device Description Installation D103412X012 February 2017...
Page 333: Glossary
DVC6200f Digital Valve Controller Instruction Manual Glossary D103412X012 February 2017 Glossary Algorithm Deadband A set of logical steps to solve a problem or Region around a reference point that must be accomplish a task. A computer program contains exceeded before a new event occurs. one or more algorithms.
Page 334 See byte Outgoing Ramp Rate Hardware Revision The rate at which the valve will move during the Revision number of the Fisher instrument Outgoing stroke of the Partial Stroke test. The hardware. The physical components of the default value is 0.25%/second.
Page 335 DVC6200f Digital Valve Controller Instruction Manual Glossary D103412X012 February 2017 Temperature Sensor Tuning A device within the FIELDVUE instrument that The adjustment of control terms or parameter measures the instrument's internal temperature. values to produce a desired control effect. Test Start Point Tuning Set The normal (not tripped) end of valve travel.
Page 336 DVC6200f Digital Valve Controller Instruction Manual Glossary February 2017 D103412X012...
Page 337: Index
DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Index Alerts Configuration, 57 Electronics, 55 enabling, 55 Environment, 59 Field Diagnostic, 54, 183 Instrument, 54 Acknowledge Option, Resource Block, 26 Performance, 65 Act On IR, 228 PlantWeb, 54, 183 Proximity, 61 Action On a Failed Test, 73 Sensor, 58...
Page 338 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 PID Function Block, 229 BLOCK_ERR Conditions AI Function Block, 287 Area Units, 68 AO Function Block, 216 ATEX, hazardous area approval, 10 CSEL Function Block, 249 DI Function Block, 319 Auto Calibration, 120 ISEL Function Block, 262 Auto PST, 77...
Page 339 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Configuration Alerts, 57 Blocks Set to Default, 58 Output Block Timeout, 57 DD Information, 130 Declaration of SEP, 11 Configuration, Initial, 5 DeltaV ProfessionalPLUS Workstation, Installing DD Configure/Setup, 23 on, 328 DeltaV Tune, for PID control loops, 229 Confirm Time, 25 Demand Stroke Time, 64...
Page 340 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Discrete Alarm Auto Acknowledge, 26 Discrete Alarm Disabled, 26 Educational Services, 12 Effective Area, 71 Discrete Input (DI) Function Block, 7, 315 Action on Failure, 319 Electrical Classification Alarm Detection, 319 Electrical Housing, 10 Hazardous Area Approvals, 10 Application Information, 319...
Page 341 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Feedforward Calculation, PID Function Block, 227 Flow Direction, 69 Flow Tends To, 70 Field Communicator Menu Structure AI Function Block, 294 FM, hazardous area approval, 10 AO Function Block, 221 Freeze Analog / Discrete Feedback, 74 CSEL Function Block, 254 DO Function Block, 313...
Page 342 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Input to Output Mapping, OS Function Block, 274 Installation, 5 I/O Options, AO Function Block, 214 Instrument Alert, Conditions, 183 I/O Processor Alert, 57 Instrument Alert Conditions, 54, 131 I/O Processor Manual Recovery, 57 Integrator Limited Hi, Self Test Status, 131 I/O Processor Shutdown, 57 Integrator Limited Lo, Self Test Status, 131...
Page 343 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 OS Function Block, 272 PID Function Block, 225 Resource Block, 23 Magnetic Feedback Assembly, removing, 138 Transducer Block, 47 MAI Channel Map, 72 Module Base MAI Function Block, parameters, 297 removing, 139 replacing, 140 Maintenance...
Page 344 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Output Block Selection, 54 PD Run, Alert, 65 Performance Alerts, 65 Output Block Timeout, 57 PD Inside Status, 65 Output Block Timeout Alert, 57 PD Run, 65 Output Block Timeout Manual Recovery, 57 Performance Critical, 65 Performance Information, 65 Output Block Timeout Shutdown, 57...
Page 345 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Pressure Cutoff Open, 52 PST Minimum Travel, 74 PST Prohibited, 77 Pressure Fallback Alert, 59 PST Randomization, 74 Pressure Fallback Auto Recovery, 51 PST Return Lead, 74 Pressure Fallback Manual Recovery, 51 PST Threshold, 66 Pressure Integral Dead Zone, 51 Push Down To, 70...
Page 346 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Restart Actions, 128 Shed Options—RCAS Mode Only AO Function Block, 211 Set Fault State, 128 PID Function Block, 225 Strategy, 129 Tag Description, 129 Shed Remote Cascade, 24 View Lists, 45 Signal Conversion, AI Function Block, 286 Device Diagnostics, 125 Write Lock, 127...
Page 347 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Stroking Time Open, 71 Mode, 17, 47 parameters, 79 Substatus Propagation, ISEL Function Block, 257 Status and Limit Propagation, 201 Supply, 59 View Lists, 114 Supply Medium, per ISO 8573-1, 9 Travel (DeChar), 60, 61 Supply Pressure Travel Accumulator, 63...
Page 348 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Travel Integral Limit Hi, 49 Tuning Pressure, 50 Travel Integral Limit Lo, 49 Travel, 48 Travel Limit Hi Hi Alert Point, 60 Tuning Set Travel Limit High High Alert, 60 Device Setup, 21 Pressure, 50 Travel Limit Low Alert, 61...
Page 349 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017 Vibration Testing, Method, 10 View Lists, 125 Weight AI Function Block, 293 DVC6200f, 11 Analog Output (AO) Function Block, 220 DVC6205f, 11 CSEL Function Block, 253 DVC6215, 11 DI Function Block, 324 Wiring and Electrical Connections, Communication DO Function Block, 312 Connections, 14...
Page 350 DVC6200f Digital Valve Controller Instruction Manual Index D103412X012 February 2017...
Page 352 Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher, FIELDVUE, ValveLink, DeltaV, and Baumann are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co.

Fisher FIELDVUEDVC6200f Instruction Manual

And Initial Configuration

Specifications

Section 1 Introduction and Specifications

Section 2 Wiring Practices

Section 3 Basic Setup

Section 4 Detailed Setup

Section 5 Calibration

Variables and Diagnostics

Section 6 Viewing Device Variables and Diagnostics

Section 7 Maintenance and Troubleshooting

Troubleshooting

Section 8 Parts

Appendix A Principle of Operation

Appendix B Field Communicator Menu Tree

Menu Tree

Appendix C Field Diagnostic Alerts

Communication

Appendix D FOUNDATION Fieldbus Communication

Appendix E Function Blocks

Installation

Appendix F Device Description Installation

Glossary

Index

Quick Links

Troubleshooting

Related Manuals for Fisher FIELDVUEDVC6200f

Summary of Contents for Fisher FIELDVUEDVC6200f

Table of Contents