Muratec MFX-1300/1700 Operating Instructions Manual page 93

Advanced features
6 Press .The now shows either:
ENTER LCD
P2:Fax#/Advan.Func.
_
7 Use the numeric keypad to enter the number exactly as your machine should dial
it, including whatever codes your phone system requires. The number can be up
to 40 characters in length:
P2:Fax#/Advan.Func.
9-5550696_
Your display shows only 20 characters at a time. To view characters beyond those
20, press t o s c r o l l t o t h e l e ft o r
Important: Do not press
8 Next, while you can still see the fax number on the
twice and then press
TIONS
9 If you want the polling to begin immediately every time you press the key, press
and skip to step 12.
ENTER
If you want to delay the polling, press
10 Next, tell your fax to carry out this delayed command one of these ways:
Option 1: Perform the command once at a certain time on a certain day of
the month. (For example, Do this at 5:05
To select this option, use the numeric keypad to enter the date and
time when the fax should perform the command:
Delayed
Enter Time: 30/17:05
Option 2: Perform the command at a certain time each day you press the
key.(For example, Do this at 5:05
To select this option, use the numeric keypad to enter 0 , 0 and then
the time the fax should perform the command:
Delayed
Enter Time: 00/17:05
11 Press , .
ENTER ENTER
12 Press to return your machine to standby mode.
STO P
3.40
P2:Fax#/Advan.Func.
o r
9-5558743_
t o s c r o l l t o t h e r i g h t .
.
ENTER
,press
LCD A D VA N C E D F U N C
.
ENTER
,
A D VA N C E D FUNCTIONS ENTER
on the 30th. )
P M
today. )
P M
Programming an F-Code transmission
For this operation to work, two things must be true:
You must know how the remote fax is using each F-Code box to which you re trans-
mitting for example, as a security box or a relay box. Different fax manufacturers
may use slightly different terms, but the concepts are the same.
You must know the remote fax s
which you want to transmit.
To program an F-Code transmission into a programmable one-touch key:
1 Press Program key,
ble one-touch number available:
Select Program No.
P2:No Number Stored
Note: I f P2 appears on the
-
.
Note: To erase a programmable one-touch key, see page 3.48.
2 Press the key that you want to program or change. Here, we ve selected P2.
Select Program No.
P2:No Number Stored
Note: If your previous command for this key was for an F-Code transmission
3 If you want to select a different programmable one-touch key than the one that
appears on the
4 Press
grammable one-touch:
Type :Communication
- sub-address and password for each box to
ITU T
, 3 , 0 , 1 , .The
A ENTER LCD
, it means that you have already entered a num-
LCD
b e r f o r P1. You can see what you programmed into P1 by pressing
you want. For example, if you set P1 for storing of the polling document,
you will see:
Select Program No.
P1:Polling Document
Press to go back to the programmable one-touch key you want to
enter.
and you want to keep this key programmed for an F-Code transmission,
use these instructions to make changes. But if you want to assign this
key to a completely different operation (for a delayed transmission, for
example), then you first must erase the stored command before program-
ming the new one.
, press that key now.
LCD
.The asks which operation you want to program into the pro-
ENTER LCD
/ /Enter
shows the first empty programma-
, i f