Asm 8 And Gasm8 Switch Settings - Nortel BCM200 Installation And Maintenance Manual

ASM 8 and GASM8 switch settings

In a single-density configuration, such as for DS30 6 or 7 when they are set to the default PDD,
only offset 1 and 2 are available to ASM 8/GASM8. In a double-density configuration, you can
install four GASM8s for each DS30 bus.
number and the dialing numbers (DNs) assigned to each DS30 number.
Table 40 ASM 8 settings
Select Select Enter these switch
bus offset
1 2
2.5 system upgraded to 3.0
on on on on on on 221-228
0
on on off on on on 229-236
1
2
on off on on on on 377-384
2
on off off on on on 385-392
3
on on on on on off 237-244
0
on on off on on off 245-252
1
3
on off on on on off 393-400
2
on off off on on off 401-408
3
on on on on off on 253-260
0
on on off on off on 261-268
1
4
on off on on off on 409-416
2
on off off on off on 417-424
3
on on on on off off 269-276
0
on on off on off off 277-284
1
5
on off on on off off 425-432
2
on off off on off off 433-440
3
on on on off on on 285-292
0
on on off off on on 293-300
1
6
on off on off on on 441-448
2
on off off off on on 449-456
3
on on on off on off 301-308
7*** 0
on on off off on off 309-316
1
*****2 on off on off on off 457-464
*****3 on off off off on off 465-472
** The extensions listed are based on a three-digit DN with a Start DN of 221. If your system has longer DNs or a
different Start DN, enter the range in the blank column.
*** If your system is configured with a 3/5 split, DS30 7 is not available.
*****Available only on systems set to double density with a 2/6 DS30 split.
GASM8 mode and country switch settings
The GASM8 has a second set of eight DIP switches on the right side, at the rear of the MBM, that
allow you to choose a mode of function, based on country of operation. These settings are
dependant on the version of the system software.
To
settings assign
these
3 4 5 6
DNs
Chapter 8 Installing a media bay module (MBM)
Table 39 shows the switch settings for each DS30
Select Enter these switch
offset settings
1 2 3
3.0 and newer systems
on on on on
0
on on off on
1
on off on on
2
on off off on
3
on on on on
0
on on off on
1
on off on on
2
on off off on
3
on on on on
0
on on off on
1
on off on on
2
on off off on
3
on on on on
0
on on off on
1
on off on on
2
on off off on
3
on on on off
0
on on off off
1
on off on off
2
on off off off
3
on on on off
0
on on off off
1
on off on off
*****2
on off off off
*****3
BCM200/400 4.0 Installation and Maintenance Guide
To
assign
these
4 5 6
DNs
on on 221-228
on on 229-236
on on 237-244
on on 245-252
on off 253-260
on off 261-268
on off 269-276
on off 277-284
off on 285-292
off on 293-300
off on 301-308
off on 309-316
off off 317-324
off off 325-332
off off 333-340
off off 341-348
on on 349-356
on on 357-364
on on 365-372
on on 373-380
on off 381-388
on off 389-396
on off 397-404
on off 405-412
129
**Custom
DN range