Nortel BCM 200 Technical Configuration Manual
Business communication manager
Hide thumbs
Also See for BCM 200:
- Installation and maintenance manual (386 pages) ,
- Overview (72 pages) ,
- Integration manual (70 pages)
Table of Contents
Related Manuals for Nortel BCM 200
Summary of Contents for Nortel BCM 200
- Page 1 Business Communication Manager BCM 200/400 Technical Configuration Guide > Technical Configuration Guide for BRI Based Video Conferencing on BCM Enterprise Solution Engineering Document Date: May 11th, 2006 Document Version: 1.1...
-
Page 2: Bcm Technical Configuration Guide V1.1 May
This engineering document contains the best information available at the time of publication in terms of supporting the application and engineering of Nortel products in the customer environment. They are solely for the use by Nortel customers and meant as a guide for network engineers and planners from a network engineering perspective. - Page 3 BCM Technical Configuration Guide V1.1 May, 2006 Abstract This Technical Configuration Guide (TCG) documents one specific application of an ISDN BRI based Polycom VideoStation 512 system. _______________________________________________________________________________________________________________________ NORTEL External Distribution...
-
Page 4: Table Of Contents
Before You Start ............................6 2.1.1 Pre-requisites............................6 2.1.2 Additional Information ..........................6 Flow................................6 MBM ................................7 ISDN DNs ...............................9 Loops ................................12 Routing ................................12 Target Line ..............................13 Multiple Loop Setup ...........................14 Polycom ...............................14 CAVEATS ............................16 BCM Diagnostics ............................16 PRI Trunking ...............................16 _______________________________________________________________________________________________________________________ NORTEL External Distribution... - Page 5 Figure 13: Call Routing - Route ..........................13 Figure 14: Target Line ............................. 14 Figure 15: Target Line - Recieved Number ......................14 Figure 16: In-service Diagnostic Loop 601 Layer 1....................16 Figure 17: Diagnostic Loop 601 Layer 2........................17 _______________________________________________________________________________________________________________________ NORTEL External Distribution...
-
Page 6: Introduction
Point to point video conference systems have become imbedded into the fabric of today’s small and medium business who are seeking cost reductions by leveraging their telecommunications infrastructure. To this end, Nortel’s Business Communications Manager (BCM) provides the necessary converged infrastructure to enable this type of application. -
Page 7: Programming
V1.1 May, 2006 2. Programming The following information is intended to supplement the existing suite of Nortel Business Communication Documentations. It is intended for an informed and experienced audience familiar with programming, administration, and maintenance of a BCM. 2.1 Before You Start 2.1.1 Pre-requisites... -
Page 8: Mbm
The objective of the following steps is to insert and activate the ISDN Basic Rate Interface (BRI) MBM into the BCM. Firstly, identify an available BUS, and set the dip switches accordingly; in this example, we are using BUS 06. Once inserted, set the programming to “Trunk Module”. _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 9: Figure 3: Bri Media Bay Module - Bus 6
Figure 3: BRI Media Bay Module - BUS 6 With the BRI MBM in place, continue the programming by selecting Module 1 and configuring this as a “BRI-ST” interface. Figure 4: BRI MBM - Module 1 _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 10: Isdn Dns
Note that the screen captures detail one of the two DNs that must be programmed. The first step is to ensure that the DNs are correctly identified as being of type ISDN. Repeat for both ISDN DNs to be associated with the video unit. _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 11: Figure 6: Isdn Dns - Dn 2484
The Calling Line ID (CLID) or Outgoing Line Identification (OLI) is the key to ensuring that the far end system will call back the originating system to complete call setup. In this case, our tests were performed on Nortel’s corporate network, which operates on a five digit dial plan. For these purposes, the OLI was set to the BCM’s prime DN (34190), and was padded with zeros to fill out a full 10 digit as if it was a complete public number. -
Page 12: Figure 8: Isdn Dns - Line Assignment
The next steps consist of giving the ISDN DNs access to the PRI network facilities. In this BCM, the PRI lines have been assigned to the pool PRI-A; use the “add” command highlighted in the figure below. Figure 9: ISDN DNs - Line Pool Access _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 13: Loops
PRI lines have been pooled into pool PRI-A, and that the access code for this pool is 6. Follow the screen captures below to ensure that the routing in your system is consistent with the customer preferences. _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 14: Target Line
Figure 13: Call Routing - Route 2.7 Target Line In this example, the programming of the target line allows the BCM to route any incoming calls with the Called Number of 34190 to be routed to DN 2468. _______________________________________________________________________________________________________________________ NORTEL External Distribution... -
Page 15: Multiple Loop Setup
It should be noted that during the development of this document, three (384 Kbps) and four (512 Kbps) loop configurations were setup and tested. 2.9 Polycom The unit utilized for our testing was a VideoStation 512 running software Release 7.2 – March 10, 2002. _______________________________________________________________________________________________________________________ NORTEL External Distribution... - Page 16 In this example Line1 B1: 00248400 Line1 B2: 00248500 ISDN Video (the values below were used for our testing) Country Code: 1 Area Code: 905 Number A: 2484 Number B: 2485 ISDN Switch Protocol: NI-1 ISDN Dialing Prefix: leave blank _______________________________________________________________________________________________________________________ NORTEL External Distribution...
-
Page 17: Caveats
Complete the programming and attempt to place a video call using BCM Monitor to see if there is activity from the video unit as it attempts to seize an outgoing line Notify Nortel support of your observations, referencing this document Figure 16: In-service Diagnostic Loop 601 Layer 1 3.2 PRI Trunking... -
Page 18: Figure 17: Diagnostic Loop 601 Layer 2
BCM Technical Configuration Guide V1.1 May, 2006 Figure 17: Diagnostic Loop 601 Layer 2 _______________________________________________________________________________________________________________________ NORTEL External Distribution... - Page 19 BCM Technical Configuration Guide V1.1 May, 2006 Contact Us: For product support and sales information, visit the Nortel Networks website at: http://www.nortel.com In North America, dial toll-free 1-800-4Nortel, outside North America dial 987-288-3700. _______________________________________________________________________________________________________________________ NORTEL External Distribution...