IBM x3690 X5 Service Manual page 233

Table 10. System x3690 X5 IMM error messages (continued)
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v See Chapter 4, "Parts listing, System x3690 X5 Types 7147, 7148, 7149, and 7192," on page 249 to determine which components
are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service
technician.
Event ID Message
IP subnet mask of network interface
modified from %1 to %2 by user
%3s.(%1 =
CIM_IPProtocolEndpoint.SubnetMask;
%2 = CIM_StaticIPAssignmentSetting
Data.SubnetMask; %3 = user ID)
IP address of default gateway
modified from %1 to %2 by user
%3s.(%1 =
CIM_IPProtocolEndpoint.Gateway
IPv4Address; %2 =
CIM_StaticIPAssignmentSetting
Data.Default
GatewayAddress; %3 = user ID)
OS Watchdog response %1 by %2.(%1
= Enabled or Disabled; %2 = user ID)
4000000d-00000000 DHCP[%1] failure, no IP address
assigned.(%1 = IP address,
xxx.xxx.xxx.xxx)
Remote Login Successful. Login ID:
%1 from %2 at IP address %3.(%1 =
user ID; %2 =
ValueMap(CIM_ProtocolEndpoint.
ProtocolIFType; %3 = IP address,
xxx.xxx.xxx.xxx)
Attempting to %1 server %2 by user
%3.(%1 = Power Up, Power Down,
Power Cycle, or Reset; %2 =
IBM_ComputerSystem.ElementName;
%3 = user ID)
40000010-00000000 Security: Userid: ' had %2 login
failures from WEB client at IP address
%3.(%1 = user ID; %2 =
MaximumSuccessiveLoginFailures
(currently set to 5 in the firmware);
%3 = IP address, xxx.xxx.xxx.xxx)
40000011-00000000 Security: Login ID: ' had %2 login
failures from CLI at %3.(%1 = user ID;
%2 =
MaximumSuccessiveLoginFailures
(currently set to 5 in the firmware);
%3 = IP address, xxx.xxx.xxx.xxx)
Severity Description
Info A user has
modified the IP
subnet mask of the
IMM.
Info A user has
modified the
default gateway IP
address of the
IMM.
Info A user has enabled
or disabled an OS
Watchdog.
Info A DHCP server has
failed to assign an
IP address to the
IMM.
Info A user has
successfully logged
in to the IMM.
Info A user has used the
IMM to perform a
power function on
the server.
Error A user has
exceeded the
maximum number
of unsuccessful
login attempts from
a Web browser and
has been prevented
from logging in for
the lockout period.
Error A user has
exceeded the
maximum number
of unsuccessful
login attempts from
the command-line
interface and has
been prevented
from logging in for
the lockout period.
Action
No action; information only.
No action; information only.
No action; information only.
1. Make sure that the
network cable is
connected.
2. Make sure that there is
a DHCP server on the
network that can assign
an IP address to the
IMM.
No action; information only.
No action; information only.
1. Make sure that the
correct login ID and
password are being
used.
2. Have the system
administrator reset the
login ID or password.
1. Make sure that the
correct login ID and
password are being
used.
2. Have the system
administrator reset the
login ID or password.
215
Chapter 3. Diagnostics