Epson AcuLaser C1100 Service Manual page 528

EPSON AcuLaser C1100
7. DEVELOPER
Name of signal line
MAG ROLL MOT ON
MAG ROLL MOT PWM
MAG ROLL MOT TG
MAG ROLL MOT CW/CCW
TEMP.
HUMI.
HOME POSITION SENSED (H)+5VDC
ANTENNA OUT
ANTENNA IN
SG
HOLD
CLOCK
ON (H) +5VDC
DEVE ROT A,XA,B,XB
DATA
CLOCK
FRONT DOOR OPEN (H)+3.3VDC
APPENDIX
Remarks
Magnet Roll Motor drive control signal
Temperature data (analog value) inside printer
measured by Sensor
Humidity data (analog value) inside printer
measured by Sensor
Home position detection signal of Deve Rotary
generated by Sensor Photo (Rotary Home
Position Sensor)
CRUME Cartridge Antenna control signal
PWBA Rotate Motor Control control signal
Deve Rotate Motor excitation signal
PWBA CRUM control signal
Front Door open/close detection signal
Wiring Connection Diagram between Parts
PWBA
MCU
PL12.2.1 P/J415
SG
10
FRONT DOOR OPENED (H) +3.3VDC
11
P/J413
+5VDC TEMP.
1
SG
2
HUMI.
3
+5VDC
4
P/J412
DATA
1
+5VDC CLOCK
2
+5VDC
3
SG
4
MOT ASSY MAG
PL11.1.4
P/J405
MAG ROLL MOT ON
1
MAG ROLL MOT PWM
2
MAG ROLL MOT TG
Interlock
3
+24VDC MAG ROLL MOT CW/CCW
4
SG
5
I/L +24VDC
6
P/J406
I/L +24VDC
1
DISP CLUTCH ON (L) +24VDC
2
+5VDC
P/J413
PULL UP +5VDC
5
SG
6
HOME POSITION SENSED (H) +5VDC
7
P/J415
ANTENNA OUT
1
ANTENNA IN
2
PWB ASSY ROT
PL12.1.10
P/J415 P/J430
SG
6 4
HOLD
7 3
CLOCK
Interlock
8 2
ON (H) +5VDC +24VDC
9 1
LV/HVPS
PL12.2.3
Interlock
+24VDC
P/J502 P/J432
I/L +24VDC
11 1
SG
12 3
Figure 7-14. DEVELOPER Connection and Wiring Diagram
Revision B
SWITCH-FRONT
DOOR
PL1.1.26
P/J125
2
1
SENSOR HUM & TEMP
PL12.1.6
P/J10 4
4
+5VDC
3
2
1
PWBA CRUM
PL12.1.11
P/J429 +5VDC
4
3
2
1
MAGNET
ROLL MOTOR
M
DISPENSE CLUTCH
P/J105
3
SENSOR ROTARY
2 HOME POSI
PL9.1.18
1
P/J106
2
ANTENNA CTRG
PL9.1.12
1
MOT
ASSY ROT
PL11.1.5
P/J433 P/J204
DEVE ROT A
1 1
I/L +24VDC
2 3
DEVE ROT XA
3 5
M
DEVE ROT B
4 7
I/L +24VDC
5 9
DEVE ROT XB
6 11
Leg_Sec007_008FB
528