Igmp / Mld Snooping Commands - D-Link xStack DES-3528 Series Cli Reference Manual

xStack® DES-3528/DES-3552 Series Layer 2 Managed Stackable Fast Ethernet Switch CLI Reference Guide

IGMP / MLD Snooping Commands

The IGMP / MLD Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate
parameters) in the following table.
Command
config igmp_snooping
config igmp_snooping rate_limit
config igmp_snooping querier
config router_ports
config router_ports_forbidden
create igmp_snooping static_group
delete igmp_snooping static_group
config igmp_snooping static_group
show igmp_snooping static_group
config igmp_snooping
data_driven_learning
show igmp_snooping
show igmp_snooping rate_limit
show igmp_snooping group
show igmp_snooping forwarding
show router_ports
show igmp_snooping statistic counter
clear igmp_snooping statistics counter
config mld_snooping
config mld_snooping querier
config mld_snooping mrouter_ports
config mld_snooping
mrouter_ports_forbidden
show mld_snooping
show mld_snooping group
show mld_snooping forwarding
Parameters
[vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable |
disable] | fast_leave [enable | disable] | report_suppression [enable |
disable]}(1)
[ports <portlist> | vlanid <vlanid_list>] [<value 1-1000> | no_limit]
[vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {query_interval
<sec 1-65535> | max_response_time <sec 1-25> | robustness_variable
<value 1-7> | last_member_query_interval <sec 1-25> | state [enable |
disable] | version <value 1-3>}
[<vlan_name 32> | vlanid <vlanid_list> ] [add | delete] <portlist>
[ <vlan_name 32> | vlanid <vlanid_list> ] [add | delete] <portlist>
[vlan<vlan_name 32> | vlanid <vlanid_list>] <ipaddr>
[vlan<vlan_name 32> | vlanid <vlanid_list>] <ipaddr>
[vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr> [add | delete]
<portlist>
{[vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr>}
[max_learned_entry <value 1-1024> | vlan_name <vlan_name> | vlanid
<vlanid_list> | all] {state [enable | disable] | aged_out [enable | disable] |
expiry_time <sec 1-65535>}(1)
{[vlan <vlan_name 32> | vlanid <vlanid_list>]}
[ports <portlist> | vlanid <vlanid_list>]
{[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist>] {<ipaddr>}}
{data_driven}
{[vlan <vlan_name 32> | vlanid <vlanid_list>]}
{[vlan <vlan_name 32> | vlanid <vlanid_list> | all]} {static | dynamic |
forbidden}
[vlan <vlan_name> | vlanid <vlanid_list> | ports <portlist>]
[vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable |
disable] | fast_done [enable | disable] | report_suppression [enable |
disable]}(1)
[vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {query_interval
<sec 1-65535> | max_response_time <sec 1-25> | robustness_variable
<value 1-7> | last_listener_query_interval <sec 1-25> | state [enable |
disable] | version <value 1-2>}(1)
[vlan <vlan_name 32> | vlanid <vlanid_list>] [add | delete] <portlist>
[vlan <vlan_name 32> | vlanid <vlanid_list>] [add | delete] <portlist>
{[vlan <vlan_name 32> | vlanid <vlanid_list>]}
{[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist>]
{<ipv6addr>}} {data_driven}
{[vlan <vlan_name 32> | vlanid <vlanid_list>]}
198