Warning Message - Yamaha CS1D Owner's Manual

Appendices

Warning Message

These messages will disappear after a short time.
Message
2TR IN DIGITAL-3 SRC TURNED OFF.
CANNOT DROP!
CANNOT UNDO!
CONTROL I/O OUT SYNC
DETECTIVE ERROR![CONSOLE]
CONTROL I/O OUT SYNC
DETECTIVE ERROR![ENGINE]
DATA TYPE CONFLICT! CANCELED.
DCA-(x) IS FOR INPUTS NOW.
DCA-(x) IS FOR OUTPUTS NOW.
DIGITAL INPUT SYNC ERROR! [2TR
IN DIGITAL-(x)]
DIGITAL INPUT SYNC ERROR! [UNIT-
(x):SLOT-(x)]
DIGITAL INPUT SYNC ERROR! [UNIT-
(x):SLOT-(x):CH-(x)/(x)]
DUPLICATE TC EVENT! CANCELED.
EFFECT CUE TURNED OFF.
MEMORY PROTECTED!
MIDI: DATA FRAMING ERROR!
MIDI: DATA OVERRUN!
MIDI: Rx BUFFER FULL!
MIDI: Tx BUFFER FULL!
MUTE GROUP-(x)IS FOR INPUTS
NOW.
MUTE GROUP-(x)IS FOR OUTPUTS
NOW.
NO DATA!
PAIRING RELEASED.
READ ONLY!
SUB IN CUE TURNED OFF.
SYNC ERROR! [COMPONENT NAME] The indicated device is not synchronized with the engine.
TC EVENT FULL! CANCELED.
TIME CODE ACTIVE! CANNOT
STORE.
TIME CODE: FRAME JUMP!
TIME CODE: TYPE MISMATCHED!
WRONG WORD CLOCK!
[COMPONENT NAME]
48
When WORD CLOCK was selected for 2TR IN3, SRC=ON changed to OFF.
You attempted to drop an EQ/COMP/GATE/GEQ graph onto a location of a
different type.
You pressed the [UNDO] switch when undo was not available.
Synchronization data from the CONTROL I/O output of the console could not
be detected.
Synchronization data from the CONTROL I/O output of the engine could not
be detected.
You attempted to execute Library Recall or Channel Copy on a channel of a
different type.
You attempted to assign an output channel to DCA-(x), to which an input
channel was already assigned (DCA 9-12).
You attempted to assign an input channel to DCA-(x), to which an output
channel was already assigned (DCA 9-12).
The signal from the device connected to 2TR IN DIGITAL-(x) is not synchro-
nized to the engine.
The input signal from the corresponding digital card -(x) of the connected
DIO8 is not synchronized to the engine (MY8-AT, TD).
The input signal from the corresponding digital card -(x) of the connected
DIO8 is not synchronized to the engine (MY8-AE).
You attempted to input an event at the same location as a previously-input
TC event.
CUE was defeated because you switched EFFECT screens.
You attempted to store by overwriting onto Write Protected data.
Invalid data was received at the selected MIDI IN.
Invalid data was received at the selected MIDI IN.
Incoming MIDI data was excessive.
Outgoing MIDI data was excessive.
You attempted to assign an output channel to MUTE GROUP-(x), to which an
input channel is already assigned. (MUTE GROUP 9-12)
You attempted to assign an input channel to MUTE GROUP-(x), to which an
output channel is already assigned. (MUTE GROUP 9-12)
Data has not been stored in the memory you attempted to recall. Alterna-
tively, the data is damaged and cannot be recalled.
When recalling, pairing was defeated since Recall Safe settings would have
caused paired channels to have different settings.
You attempted to store by overwriting Read Only data.
CUE was turned off because you switched the SUB IN screen.
Registration was cancelled because no further TC events could be regis-
tered.
The store operation is not possible because the TC EVENT RECALLING
function is set to "ENABLE."
The currently-input time code has jumped frames or has run away.
The currently-input time code is of a type different from the specified type.
The engine is not synchronized to the source selected by MASTER CLOCK
SELECT in the SYS/W.CLOCK function WORD CLOCK screen.
Explanation