Yamaha CS1D Owner's Manual page 53

7. In the STEREO OUTPUT block, raise the ST OUT-
PUT A channel fader.
At this time, the STEREO A L/R meters in the meter
bridge block will show the output level of the STE-
REO A channel.
CLIP CLIP
-4 -4
-8 -8
-12 -12
-16 -16
-20 -20
-24 -24
-30 -30
-40 -40
-50 -50
-70 -70
L R L R
STEREO A STEREO B
STEREO A L/R meters
If the signal can now be heard from your monitor
system, you have verified that the output unit/card to
which the source is connected is functioning cor-
rectly.
8. As necessary, use the same procedure to check the
operation of other output units or cards.
If the input source could not be monitored, check
the following points.
Meter LEDs in the INPUT block do not light
Is the input source connected appropriately?
Check the unit/card to which the input source is
connected ( p.32).
When using a mic/line input card (LMY2-ML), is
the input source connected to input jacks 1A and
2A?
When the PM1D system is in the default state,
input jacks 1B or 2B cannot be used without
changing the settings. Re-connect to input jacks 1A
and 2A ( p.32).
Has the output unit/card to which the input source
is connected been correctly patched to the input
channel?
Check the settings of the IN PATCH screen
( p.33).
Meter bridge block
CLIP
-4
-8
HOUR MINU
TIM
-12
-16
-20
-24
NUMBER
-30
-40
-50
SCEN
-70
L R
CUE
Checking the operation of an output unit
In the SELECTED INPUT CHANNEL block, has
the MODULE [FLIP] switch been turned on (LED
lit)?
When the MODULE [FLIP] switch is on, the mod-
ules of INPUT blocks 1 and 2 will be exchanged.
Press the MODULE [FLIP] switch to make the
LED go dark. ("CS1D Reference Manual (Hard-
ware)" p.5)
In the MASTER block GLOBAL LAYER section,
has the [49-96] switch been turned on (LED lit)?
On the 96 channel model when the GLOBAL
LAYER [49-96] switch is on (LED lit), channels
49–96 will be selected as the input channels that
are controlled from the top panel of the CS1D.
{This switch has no function on the 48 channel
model.} To control channels 1–48, press the GLO-
BAL LAYER [1-48] switch. ("CS1D Reference
Manual (Hardware)"
STEREO A L/R meters in the meter bridge block do not
light
Is the input channel [ON] switch turned off?
In the INPUT block, turn on the [ON] switch for
input channels 1/49 and 2/50 ( p.44).
Is the [TO ST] switch of the input channel turned
off?
In the INPUT block, turn on the [TO ST] switch
for channels 1/49 and 2/50 ( p.44).
Is the input channel fader lowered?
In the INPUT block, raise the faders for input
channels 1/49 and 2/50 ( p.44).
STEREO A L/R meters in the meter bridge block are lit,
but there is no output from the output unit
Is the STEREO A channel STEREO [ON] switch
turned off?
In the STEREO OUTPUT block, turn on the STE-
REO [ON] switch of the STEREO A channel
( p.44).
Is the STEREO fader of the STEREO A channel
lowered?
In the STEREO OUTPUT block, raise the STEREO
fader of the STEREO A channel ( p.45).
Is the monitor system connected appropriately?
Check the connections of the monitor system
( p.39).
Are the output channels patched appropriately?
In the OUT PATCH screen, check whether the
STEREO A L/R channels are appropriately patched
to the output unit/card to which your monitor sys-
tem is connected ( p.42).
p.5)
45