Intel 8XC196MC User Manual page 467

8XC196MC, MD, MH USER'S MANUAL
Name Type
P2.7:0 I/O
P3.7:0 I/O
P4.7:0 I/O
P5.7:0 I/O
P6.7:0 O
B-18
Table B-6. Signal Descriptions (Continued)
Port 2
This is a standard, 8-bit, bidirectional port that is multiplexed with individually
selectable special-function signals.
P2.6 is multiplexed with a special test-mode-entry function. If this pin is held low
during reset, the device will enter a reserved test mode, so exercise caution if
you use this pin for input. If you choose to configure this pin as an input, always
hold it high during reset and ensure that your system meets the V
(see datasheet) to prevent inadvertent entry into ONCE mode.
On the 8XC196MC and MD, port 2 is multiplexed as follows: P2.0/EPA0/PVER,
P2.1/EPA1/PALE#, P2.2/EPA2/PROG#, P2.3/EPA3, P2.4/COMP0/AINC#,
P2.5/COMP1/PACT#, P2.6/COMP2/CPVER, and P2.7/COMP3.
On the 8XC196MH, port 2 is multiplexed as follows: P2.0/EPA0/PVER,
P2.1/SCLK0#/BCLK0/PALE#, P2.2/EPA1/PROG#, P2.3/COMP3,
P2.4/COMP0/AINC#, P2.5/COMP1/PACT#, P2.6/COMP2/CPVER, and
P2.7/SCLK1#/BCLK1.
Port 3
This is a memory-mapped, 8-bit, bidirectional port with programmable open-
drain or complementary output modes. The pins are shared with the
multiplexed address/data bus, which has complementary drivers.
P3.7:0 are multiplexed with AD7:0 and PBUS.7:0.
Port 4
This is a memory-mapped, 8-bit, bidirectional port with programmable open-
drain or complementary output modes. The pins are shared with the
multiplexed address/data bus, which has complementary drivers.
P4.7:0 are multiplexed with AD15:8 and PBUS15:8.
Port 5
This is a memory-mapped, 8-bit, bidirectional port that is multiplexed with
individually selectable control signals.
P5.4 is multiplexed with the ONCE# function. If this pin is held low during reset,
the device will enter ONCE mode , so exercise caution if you use this pin for
input. If you choose to configure this pin as an input, always hold it high during
reset and ensure that your system meets the V
to prevent inadvertent entry into ONCE mode.
Port 5 is multiplexed as follows: P5.0/ALE/ADV#, P5.1/INST, P5.2/WR#/WRL#,
P5.3/RD#, P5.4/ONCE#, P5.5/BHE#/WRH#, P5.6/READY, and
P5.7/BUSWIDTH.
Port 6
This is a standard, 8-bit, output-only port that is multiplexed with the special
functions of the waveform generator and PWM peripherals. The WG_OUT
register configures the pins, establishes the output polarity, and controls
whether changes to the outputs are synchronized with an event or take effect
immediately.
Port 6 is multiplexed as follows: P6.0/WG1#, P6.1/WG1, P6.2/WG2#,
P6.3/WG2, P6.4/WG3#, P6.5/WG3, P6.6/PWM0, and P6.7/PWM1.
Get other manuals https://www.bkmanuals.com
Description
specification (see datasheet)
IH
specification
IH