Codes - Code Types; User Codes - Bentel Security KYO 320 Installation Manual

Codes - Code Types

When programming the Codes, you must also select
which functions are to be enabled.
The system manages 19 Code Types:
Ø 16 User Codes
Ø 2 Installer Codes
+
Code Type 19 is reserved for Installer Code No.
200 , and CANNOT be programmed.
The Code Types page will allow you to select the User
Code and Installer Code functions, as follows.
On the left side of the Code Types page is a Table with
a list of the 19 Code types.
No. This is the Code Type ID Number:
Ø Code Types no. 01 to 16 are reserved for User
Codes;
Ø Code Types no. 17 and 18 are reserved for Installer
Codes;
Ø Code Type no. 19 is reserved for Installer Code No.
200 and CANNOT be programmed.
Description This editable field (16 characters) is for the
label that will identify the Code Type. The label will be used
in the Code Type on the Users and Installers pages.
The functions of the Code Type (selected from the
Code Type list) can be programmed on the right side of
the page.
The User Code functions are described in the following
paragraph.
The Installer Code functions are described in the "In -
staller Codes" paragraph.
n User Codes
This paragraph provides a general description of the
User Code functions — refer to the USER'S MANUAL
for further information.
+
The Partition related functions will affect ONLY
those Partitions common to both the Code and
Keypad in use.
Panel Reset This operation will:
Ø terminate all the Control Panel Events (refer to Ta -
ble 7 on page 60) and Generic Events (see Table 8
on page 61);
Ø restore to standby any Outputs associated with the
terminated events (refer to the previous points);
Ø delete memory of BPI Device Tamper, Tamper Line
Alarm, Control Panel Tamper, False Key and Super -
vised Output Tamper events.
+
If the Alarm conditions are still present after Reset
(approx. 2 seconds), the Control panel will trigger
the relative Alarm Events again.
80
Stop Alarms As per Panel Reset but for the Stop
Alarms option.
NOTE: If the Stop Alarms option is enabled, the events
listed in the previous paragraph will be ignored.
Arm/Disarm from User Menu If this option is en-
abled, the Code will be able to Arm (in Stay/Away mode
and Stay 0 Delay mode) and Disarm its Partitions, via
the Arm option from the USER MENU.
Request Overtime If this option is enabled, the Code
will be able to make Overtime Requests for its Partitions.
Request Teleservice If this option is enabled, the
Code will be able to Enable/Disable Teleservice.
Enab./Disab. Scheduler If this option is enabled, the
Code will be able to Enable/Disable the Scheduler on its
Partitions.
Enab./Disab. Teleservice If this option is enabled, the
Code will be able to Enable/Disable Teleservice.
Enab./Disab. Answering Machine If this option is en-
abled, the Code will be able to Enable/Disable An-
swering function.
Enab./Disab. Keypad Buzzer If this option is enabled,
the Code will be able to Enable/Disable the Keypad
buzzer.
Phone Number Modify If this option is enabled, the
Code will be able to edit the Telephone Numbers in the
General Phonebook.
Date/time Modify If this option is enabled, the Code
will be able to set the Control Panel date and time.
Reset Warning PC Progr. If this option is enabled,
the Code will be able to restore fault signals triggered by
computer or Keypad programming.
Keypad Test If this option is enabled, the Code will be
able to run the Keypad test.
Squawk If this option is enabled, the Code will be able
to run the test on Output no. 1.
Output ON/OFF If this option is enabled, the Code will
be able to switch the Reserved Outputs ON and OFF.
Bypass/Unbypass Zones If this option is enabled, the
Code will be able to Bypass/Unbypass and view the sta-
tus of the Zones of its Partitions.
Reset/Play/Restart Continuous Rec. If this option is
enabled, the Code will be able to manage the Continu-
ous Recording function.
Play/Rec. Memo If this option is enabled, the Code will
be able to listen to and record Voice Memos at the Keypad.