NEC 78K0 User Manual page 531

CHAPTER 30 ELECTRICAL SPECIFICATIONS (STANDARD PRODUCTS, (A) GRADE PRODUCTS)
X1 Oscillator Characteristics
= −40 to +85°C, 2.7 V ≤ V
(T
A
Resonator Recommended Circuit
Ceramic
X1 X2
V
SS
resonator
C2
C1
Crystal
X1 X2
V
SS
resonator
C2
C1
External
Note 3
clock
X1 X2
Notes 1. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time.
2. When the REGC pin is connected to V
3. Connect the REGC pin directly to V
Cautions 1. When using the X1 oscillator, wire as follows in the area enclosed by the broken lines in the
above figures to avoid an adverse effect from wiring capacitance.
• Keep the wiring length as short as possible.
• Do not cross the wiring with the other signal lines.
• Do not route the wiring near a signal line through which a high fluctuating current flows.
• Always make the ground point of the oscillator capacitor the same potential as V
• Do not ground the capacitor to a ground pattern through which a high current flows.
• Do not fetch signals from the oscillator.
2. Since the CPU is started by the Ring-OSC after reset is released, check the oscillation
stabilization time of the X1 input clock using the oscillation stabilization time status register
(OSTC). Determine the oscillation stabilization time of the OSTC register and oscillation
stabilization time select register (OSTS) after sufficiently evaluating the oscillation stabilization
time with the resonator to be used.
≤ 5.5 V, 2.7 V ≤ AV
= EV
DD DD
Parameter
Oscillation When a capacitor
Note 1
frequency (f ) is connected to
XP
the REGC pin
When the REGC
pin is connected
directly to V
Oscillation When a capacitor
Note 1
frequency (f ) is connected to
XP
the REGC pin
When the REGC
pin is connected
directly to V
4.0 V ≤ V
X1 input
Note 1
frequency (f )
3.3 V ≤ V
XP
2.7 V ≤ V
4.0 V ≤ V
X1 input high-
/low-level width
3.3 V ≤ V
(t , t )
XPH XPL
2.7 V ≤ V
*
via a capacitor (1
SS
.
DD
User's Manual U15947EJ2V0UD
≤ V
, V = EV = AV
REF DD SS SS
Conditions
4.0 V ≤ V
< 5.5 V
DD
Note 2
4.0 V ≤ V ≤ 5.5 V
DD
3.3 V ≤ V
< 4.0 V
DD
DD
2.7 V ≤ V
< 3.3 V
DD
4.0 V ≤ V
< 5.5 V
DD
Note 2
4.0 V ≤ V ≤ 5.5 V
DD
3.3 V ≤ V
< 4.0 V
DD
DD
2.7 V ≤ V
< 3.3 V
DD
≤ 5.5 V
DD
< 4.0 V
DD
< 3.3 V
DD
≤ 5.5 V
DD
< 4.0 V
DD
< 3.3 V
DD
µ
F: recommended).
= 0 V)
SS
MIN. TYP. MAX. Unit
2.0 8.38 MHz
2.0 10 MHz
2.0 8.38
2.0 5.0
2.0 8.38 MHz
2.0 10 MHz
2.0 8.38
2.0 5.0
2.0 10 MHz
2.0 8.38
2.0 5.0
46 500 ns
56 500
96 500
.
SS
531