WAGO 750-495/040-00 Series Manual page 6

6 Table of Contents
7.7.1.3.1
7.7.1.3.2
7.7.2
7.7.2.1
7.7.2.1.1
7.7.2.1.2
7.7.2.2
7.7.2.2.1
7.7.2.3
7.7.2.3.1
7.7.2.3.2
8 Commissioning ..................................................................................... 177
8.1 General .............................................................................................. 177
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.1.6
8.2 Settings and Measured Values up to Firmware 04 .............................. 185
8.2.1
8.2.2
8.2.3
8.2.4
8.3 Settings and Measured Values for 4-Wire Wye (4-W) with Firmware
Versions 05 and above ....................................................................... 195
8.3.1
8.3.2
8.3.3
8.3.4
8.3.5
8.3.6
8.3.6.1
8.3.6.2
8.3.6.3
8.3.6.4
8.3.6.5
8.3.6.6
8.3.6.7
8.3.6.8
8.4 Settings and Measured Values for 3-Wire Wye/Delta (3-W) ............... 214
8.4.1
8.4.2
8.4.3
8.4.4
8.4.5
8.4.5.1
8.4.5.2
Manual
Version 1.2.0
750-495/040-00x 3-Phase Power Measurement Module 690 V
3-Wattmeter Method (Artificial Star Point - ASP) .................. 164
2-Wattmeter Method (Aron Circuit/Blondel's Theorem) ......... 165
Measurement of U over 400 V
LL
Measurements in Y Networks with Star Points Grounded on
the Source Side ......................................................................... 167
3-Wattmeter Method (Artificial Star Point - ASP) .................. 167
2-Wattmeter Method (Aron Circuit/Blondel's Theorem) ......... 169
Measurement in Δ Networks with a Grounded Line Conductor .. 171
2-Wattmeter Method (Aron Circuit/Blondel's Theorem) ......... 171
Measurement in Ungrounded Y/Δ Networks .............................. 173
3-Wattmeter Method (Artificial Star Point - ASP) .................. 173
2-Wattmeter Method (Aron Circuit/Blondel's Theorem) ......... 175
Software Interface .......................................................................... 178
"Start" Ribbon ................................................................................ 180
"Measured Value Views" Menu ...................................................... 180
Status Bar ...................................................................................... 181
"Settings" Dialog ............................................................................ 182
Setting Measurement Units ............................................................ 184
Tabs "Phase L1", "Phase L2" and "Phase L3" ............................... 185
"Neutral Conductor" Tab ................................................................ 187
"I/O Module" Tab ............................................................................ 188
"Factory Settings" Tab .................................................................... 193
"I/O Module" Tab ............................................................................ 195
Tabs "Phase L1," "Phase L2" and "Phase L3" ................................ 198
"Neutral Conductor" Tab ................................................................ 200
"Energy" Tab .................................................................................. 201
"Factory Settings" Tab .................................................................... 203
Displaying the Measured Values with WAGO-I/O-CHECK ............. 205
"Overview" View ........................................................................ 205
"Phase L1 / L2 / L3 Measurements" View .................................. 206
"Currents/Voltages" View ........................................................... 207
"Power" View ............................................................................. 208
"Energies" View ......................................................................... 209
"Harmonics" View ...................................................................... 210
"Measurement Recording" View ................................................ 212
"Information" View ..................................................................... 213
"I/O Module" Tab ............................................................................ 214
Tabs "Phase L1," "Phase L2" and "Phase L3" ................................ 217
"Energy" Tab .................................................................................. 219
"Factory Settings" Tab .................................................................... 220
Displaying the Measured Values with WAGO-I/O-CHECK ............. 222
"Overview" View ........................................................................ 222
"Harmonics" View ...................................................................... 223
WAGO-I/O-SYSTEM 750 XTR
................................................ 167
RMS