WAGO 750-495/040-00 Series Manual page 17

WAGO-I/O-SYSTEM 750 XTR
750-495/040-00x 3-Phase Power Measurement Module 690 V
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos : 20.15 /Alle Serien (Allgemeine M odul e)/Sic herheits- und sonstige Hinweis e/Gefahr/Gefahr: Leitung en nur i n s pannungsfrei em Z ustand ansc hliess en oder tr ennen @ 16\mod_1372153982130_21.doc x @ 124277 @ @ 1
Only connect or disconnect lines when power is safely isolated!
The lines to the device can carry hazardous voltages and currents. Contact with
the lines when live can result in severe injury or death. Therefore, read and
observe the following safety rules before you perform work on the device:
1. Disconnect the respective system component from the power supply.
2. Secure the system component against unintentional restart.
3. Check if the voltage is positively isolated.
Pos : 20.16 /Alle Serien (Allgemeine M odul e)/Sic herheits- und sonstige Hinweis e/Vorsic ht/Vorsic ht: H eiße Oberfl äc he nic ht berühren! (allgemein) @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos : 20.17 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en (alte Struktur)/Sic her heits- und s onstige Hi nweis e/Ac htung/Ac htung: 1A bz w. 5A Eingangsstr om nicht überschr eiten! @ 15\mod_1366120670473_21.doc x @ 117163 @ @ 1
Note the max. continuous input current of 1 A resp. 5 A!
The max. continuous input current is 1 A resp. 5 A. If needed install additional
current transformers with an appropriate transforming ratio!
Pos : 20.18.1 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en (alte Struktur)/Sic her heits- und s ons tige Hi nweis e/Ac htung/Ac htung: Ei nwandfrei e Kontakti erung z ur Tragsc hiene gewährl eisten! @ 34\mod_1550481407638_21.doc x @ 530599 @ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos : 20.18.2 /Alle Serien (Allgemeine M odul e)/Sic herheits- und s onstige Hinweise/Achtung/Ac htung: D efekte oder bes chädigte Ger äte aus tausc hen! @ 6\mod_1260180857358_21.doc x @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos : 20.18.3 /Alle Serien (Allgemeine M odul e)/Sic herheits- und s onstige Hinweise/Achtung/Ac htung: Geräte vor kriec henden und isoli erenden Stoffen sc hützen! @ 6\mod_1260181036216_21.doc x @ 46747 @ @ 1
Important Notes 17
Manual
Version 1.2.0