Danfoss VLT AutomationDrive FC 360 Programming Manual page 149

Parameter Lists
5.2.24 37-** Application Settings
Par. No. # Parameter description
37-0* Application Mode
37-00 Application Mode
37-1* Position Control
37-01 Pos. Feedback Source
37-02 Pos. Target
37-03 Pos. Type
37-04 Pos. Velocity
37-05 Pos. Ramp Up Time
37-06 Pos. Ramp Down Time
37-07 Pos. Auto Brake Ctrl
37-08 Pos. Hold Delay
37-09 Pos. Coast Delay
37-10 Pos. Brake Delay
37-11 Pos. Brake Wear Limit
37-12 Pos. PID Anti Windup
37-13 Pos. PID Output Clamp
37-14 Pos. Ctrl. Source
37-15 Pos. Direction Block
37-16 Pos. Power Recovery
37-17 Pos. Ctrl Fault Behaviour
37-18 Pos. Ctrl Fault Reason
37-19 Pos. New Index
37-2* Center Winder1 set-up
37-20 Winder Mode Selection
37-21 Tension Set Point
37-22 Taper Set Point
37-23 Partial Roll Diameter Value
37-24 Core1 Diameter
37-25 Core2 Diameter
37-26 Winder Jog Speed
37-27 TLD Low Limit
37-28 TLD High Limit
37-29 TLD Timer
37-30 TLDOnDelay
37-31 Diameter Limit Detector
37-32 Initial Diameter Measurement
37-33 Diameter Measurement Input
37-34 Reading at Core
37-35 Reading at Full Roll
37-36 Tension Set Point Input
37-37 Taper Set Point Input
37-38 Tension Feedback Input
37-39 Tension Feedback Type
37-40 Center Winder Cmd Src
37-41 Diameter Change Rate
37-42 Tapered Tension Change Rate
MG06C702
Programming Guide
Default value
[0] Drive mode
[0] 24 V Encoder
0 N/A
[0] Absolute
100 RPM
5000 ms
5000 ms
[1] Enable
0 ms
200 ms
200 ms
0 N/A
[1] Enable
1000 N/A
[0] DI
[0] No Blocking
[1] Enable
[0] Ramp Down&Brake
[0] No Fault
0 N/A
[0] Wind
0%
0%
5%
5%
5%
0%
0%
0%
0.001 s
[1] Enabled
100%
[0] Set diameter when
diameter reset
[0] No Function
0 N/A
0 V
[0] Par.3721
[0] Par.3722
[0] No Function
[0] Load cell
[1] Parameter 3754~3759
control the functions
0.001%
0.1%
Danfoss A/S © 06/2017 All rights reserved.
2-set-up Change Conversio
during n index
operation
1 set-up FALSE –
1 set-up FALSE –
1 set-up FALSE 0
1 set-up FALSE –
1 set-up FALSE 67
1 set-up FALSE -3
1 set-up FALSE -3
1 set-up TRUE –
1 set-up TRUE -3
1 set-up TRUE -3
1 set-up TRUE -3
1 set-up TRUE 0
1 set-up TRUE –
1 set-up TRUE 0
1 set-up TRUE –
1 set-up TRUE –
1 set-up TRUE –
1 set-up FALSE –
1 set-up TRUE –
1 set-up TRUE –
1 set-up FALSE –
1 set-up TRUE -1
1 set-up TRUE -1
1 set-up FALSE -3
1 set-up FALSE -3
1 set-up FALSE -3
1 set-up TRUE 0
1 set-up TRUE -1
1 set-up TRUE -1
1 set-up TRUE -3
1 set-up TRUE –
1 set-up TRUE -3
1 set-up FALSE –
1 set-up FALSE –
1 set-up TRUE -2
1 set-up TRUE -2
1 set-up FALSE –
1 set-up FALSE –
1 set-up FALSE –
1 set-up FALSE –
1 set-up TRUE –
1 set-up TRUE -3
1 set-up TRUE -1
Type
Uint8
Uint8
Int32
Uint8
5 5
Uint16
Uint32
Uint32
Uint8
Uint32
Uint16
Uint16
Uint32
Uint8
Uint16
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint16
Int16
Uint32
Uint32
Uint32
Uint8
Uint16
Uint16
Uint16
Uint8
Uint32
Uint8
Uint8
Int16
Int16
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
147