Danfoss VLT AutomationDrive FC 360 Programming Manual page 139

Parameter Lists
5.2.10 9-** PROFIdrive
Par. No. # Parameter description
9-00 Setpoint
9-07 Actual Value
9-15 PCD Write Configuration
9-16 PCD Read Configuration
9-18 Node Address
9-19 Drive Unit System Number
9-22 Telegram Selection
9-23 Parameters for Signals
9-27 Parameter Edit
9-28 Process Control
9-44 Fault Message Counter
9-45 Fault Code
9-47 Fault Number
9-52 Fault Situation Counter
9-53 PROFIBUS Warning Word
9-63 Actual Baud Rate
9-64 Device Identification
9-65 Profile Number
9-67 Control Word 1
9-68 Status Word 1
9-70 Programming Set-up
9-71 PROFIBUS Save Data Values
9-72 PROFIBUSDriveReset
9-75 DO Identification
9-80 Defined Parameters (1)
9-81 Defined Parameters (2)
9-82 Defined Parameters (3)
9-83 Defined Parameters (4)
9-84 Defined Parameters (5)
9-90 Changed Parameters (1)
9-91 Changed Parameters (2)
9-92 Changed Parameters (3)
9-93 Changed Parameters (4)
9-94 Changed Parameters (5)
9-99 PROFIBUS Revision Counter
MG06C702
Programming Guide
Default value 2-set-up
0 N/A All set-ups
0 N/A All set-ups
ExpressionLimit 1 set-up
ExpressionLimit 1 set-up
126 N/A 1 set-up
1037 N/A All set-ups
[100] None 1 set-up
0 All set-ups
[1] Enabled 1 set-up
[1] Enable cyclic master 1 set-up
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
[255] No baudrate found All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
[9] Active Set-up 1 set-up
[0] Off All set-ups
[0] No action 1 set-up
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
0 N/A All set-ups
Danfoss A/S © 06/2017 All rights reserved.
Change Conversion
during index
operation
TRUE 0 Uint16
FALSE 0 Uint16
TRUE – Uint16
TRUE – Uint16
TRUE 0
TRUE 0 Uint16
TRUE –
TRUE – Uint16
FALSE – Uint16
FALSE –
TRUE 0 Uint16
TRUE 0 Uint16
TRUE 0 Uint16
TRUE 0 Uint16
TRUE 0
TRUE –
TRUE 0 Uint16
TRUE 0 OctStr[0]
TRUE 0
TRUE 0
TRUE –
TRUE –
FALSE –
TRUE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
FALSE 0 Uint16
TRUE 0 Uint16
Type
Uint8
5 5
Uint8
Uint8
V2
Uint8
V2
V2
Uint8
Uint8
Uint8
137