Danfoss VLT AutomationDrive FC 360 Programming Manual page 88

Parameter Descriptions
9-23 Parameters for Signals
Option:
[625] Terminal 54 High Ref./Feedb. Value
[676] Terminal 45 Output Bus Control
[696] Terminal 42 Output Bus Control
[733] Process PID Proportional Gain
[734] Process PID Integral Time
[735] Process PID Differentiation Time
4 4
[748] PCD Feed Forward
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor current
[1615] Frequency [%]
[1616] Torque [Nm]
[1617] Speed [RPM]
[1618] Motor Thermal
[1622] Torque [%]
[1630] DC Link Voltage
[1633] Brake Energy /2 min
[1634] Heatsink Temp.
[1635] Inverter Thermal
[1638] SL Controller State
[1639] Control Card Temp.
[1650] External Reference
[1652] Feedback[Unit]
[1653] Digi Pot Reference
[1657] Feedback [RPM]
[1660] Digital Input
[1661] Terminal 53 Setting
[1662] Analog input 53
[1663] Terminal 54 Setting
[1664] Analog input 54
[1665] Analog output 42 [mA]
[1667] Pulse input 29 [Hz]
[1668] Pulse input 33 [Hz]
[1669] Pulse output 27 [Hz]
[1670] Pulse output 29 [Hz]
[1671] Relay output
[1672] Counter A
[1673] Counter B
[1679] Analog output 45 [mA]
86
®
VLT AutomationDrive FC 360
9-23 Parameters for Signals
Function: Option:
[1680]
[1682]
[1684]
[1685]
[1690]
[1691]
[1692]
[1693]
[1694]
[1695]
[1697]
[3401]
[3402]
[3403]
[3404]
[3405]
[3406]
[3407]
[3408]
[3409]
[3410]
[3421]
[3422]
[3423]
[3424]
[3425]
[3426]
[3427]
[3428]
[3429]
[3430]
[3450]
[3456]
9-27 Parameter Edit
Option:
[0]
[1]
*
Danfoss A/S © 06/2017 All rights reserved.
Fieldbus CTW 1
Fieldbus REF 1
Comm. Option STW
FC Port CTW 1
Alarm Word
Alarm Word 2
Warning Word
Warning Word 2
Ext. Status Word
Ext. Status Word 2
Alarm Word 3
PCD 1 Write For Application
PCD 2 Write For Application
PCD 3 Write For Application
PCD 4 Write For Application
PCD 5 Write For Application
PCD 6 Write For Application
PCD 7 Write For Application
PCD 8 Write For Application
PCD 9 Write For Application
PCD 10 Write For Application
PCD 1 Read For Application
PCD 2 Read For Application
PCD 3 Read For Application
PCD 4 Read For Application
PCD 5 Read For Application
PCD 6 Read For Application
PCD 7 Read For Application
PCD 8 Read For Application
PCD 9 Read For Application
PCD 10 Read For Application
Actual Position
Track Error
Function:
Parameters can be edited via PROFIBUS, the
standard RS485 interface, or the LCP.
Disabled Disable editing via PROFIBUS.
Enabled Enable editing via PROFIBUS.
Function:
MG06C702