YASKAWA V1000 Series Technical Manual page 72

4.5 Application Presets
No.
C6-02
H2-03
L2-01
L8-03
L8-38
No. Parameter Name
b1-01 Frequency Reference Selection
b1-02 Run Command Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-02 Carrier Frequency Selection
d2-01 Frequency Reference Upper Limit
d2-02 Frequency Reference Lower Limit
No.
A1-02
b1-04
C1-01
C1-02
C6-01
E1-03
L2-01
L3-04
No. Parameter Name
b1-01 Frequency Reference Selection
b1-02 Run Command Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
No.
A1-02
b1-01
b6-01
b6-02
C1-01
C1-02
C6-01
C6-02
d1-01
d1-02
d1-03
E1-03
H2-02
H2-03
L2-03
L3-04
L4-01
L4-02
L6-01
L6-02
L6-03
L8-05
L8-07
L8-38
L8-41
Note: A sequence to release the brake is needed when the multi-function output photocoupler P2-PC closes.
information.
Note: Perform Auto-Tuning after selecting the Hoist Application Preset.
No. Parameter Name
A1-02 Control Method Selection
b1-01 Frequency Reference Selection
b6-01 Dwell Reference at Start
72
Parameter Name
Carrier Frequency Selection
Terminals P2 Function Selection (open-collector)
Momentary Power Loss Operation Selection
Overheat Pre-Alarm Operation Selection
Carrier Frequency Reduction
Table 4.12 Parameters Automatically Saved as Preferred (A2-01 to A2-16)
Table 4.13 Compressor Application: Parameters and Settings
Parameter Name
Control Method Selection
Reverse Operation Selection
Acceleration Time 1
Deceleration Time 1
Duty Rating
V/f Pattern Selection
Momentary Power Loss Operation Selection
Stall Prevention Selection during Deceleration
Table 4.14 Parameters Automatically Saved as Preferred (A2-01 to A2-16)
Table 4.15 Crane Application (Hoist): Parameters and Settings
Parameter Name
Control Method Selection
Frequency Reference Selection
Dwell Reference at Start
Dwell Time at Start
Acceleration Time 1
Deceleration Time 1
Duty Rating
Carrier Frequency Selection
Frequency Reference 1
Frequency Reference 2
Frequency Reference 3
V/f Pattern Selection
Terminals P1 Function Selection (open-collector)
Terminals P2 Function Selection (open-collector)
Momentary Power Loss Minimum Baseblock Time
Momentary Power Loss Voltage Recovery Ramp Time
Speed Agreement Detection Level
Speed Agreement Detection Width
Torque Detection Selection 1
Torque Detection Level 1
Torque Detection Time 1
Input Phase Loss Protection Selection
Output Phase Loss Protection
Carrier Frequency Reduction
Current Alarm Selection
Table 4.16 Parameters Automatically Saved as Preferred (A2-01 to A2-16)
Optimum Setting
3: 8.0 kHz
39: Watt Hour Pulse Output
2: CPU Power Active - Drive will restart if power returns prior to
control power supply shut down.
4: Derated operation
2: Carrier frequency derating across entire frequency range.
No. Parameter Name
E1-03 V/f Pattern Selection
E1-04 Max Output Frequency (FMAX)
E2-01 Motor Rated Current
H3-11 Terminal A2 Gain Setting
H3-12 Frequency Reference (Current) Terminal A2 Input Bias
L2-01 Momentary Power Loss Operation Selection
L8-03 Overheat Pre-Alarm Operation Selection
o4-12 kWH Monitor Initial Value Selection
Optimum Setting
0: V/f control
1: Reverse prohibited
5.0 s
5.0 s
0: Heavy Duty
0FH
1: Enabled
1: Enabled
No. Parameter Name
E1-03 V/f Pattern Selection
E1-07 Mid Output Frequency (FB)
E1-08 Mid Output Frequency Voltage (VC)
E2-01 Motor Rated Current
Optimum Setting
2: Open Loop Vector Control
0: Operator
3.0 Hz
0.3 s
3.0 s
3.0 s
0: Heavy Duty
2: 5 kHz
6.0 Hz
30.0 Hz
60.0 Hz
0FH
37: During frequency output
5: Frequency Detection 2 (FOUT)
0.3 s
0: Disabled
2.0 Hz
0.0 Hz
8: UL3 at RUN -Fault
5%
0.5 s
1: Enabled
1: Enabled
0: Derated when operating at 6 Hz or less
1: Enabled (alarm is output)
Refer to Hoist Application Preset Specifics on page 73
No. Parameter Name
d1-02 Frequency Reference 2
d1-03 Frequency Reference 3
E1-08 Mid Output Frequency Voltage (VC)
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
for more