YASKAWA V1000 Series Technical Manual page 106

5.1 A: Initialization
No.
b1-02 Run Command Selection
b1-04 Reverse Operation Selection
b3-01 Speed Search Selection at Start
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
E1-03 V/f Pattern Selection
4: HVAC Fan Application: Parameters and Settings
No.
A1-02 Control Method Selection
b1-04 Reverse Operation Selection
C6-01 Duty Rating
C6-02 Carrier Frequency Selection
H2-03 Terminals P2 Function Selection (open-collector)
L2-01 Momentary Power Loss Operation Selection
L8-03 Overheat Pre-Alarm Operation Selection
L8-38 Carrier Frequency Reduction
Parameters below are automatically saved as Preferred Parameters (A2-01 to A2-16):
No.
b1-01 Frequency Reference Selection
b1-02 Run Command Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-02 Carrier Frequency Selection
d2-01 Frequency Reference Upper Limit
d2-02 Frequency Reference Lower Limit
5: Compressor Application: Parameters and Settings
No.
A1-02 Control Method Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-01 Duty Rating
E1-03 V/f Pattern Selection
L2-01 Momentary Power Loss Operation Selection
L3-04 Stall Prevention Selection during Deceleration
Parameters below are automatically saved as Preferred Parameters (A2-01 to A2-16):
No.
b1-01 Frequency Reference Selection
b1-02 Run Command Selection
b1-04 Reverse Operation Selection
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
6: Hoist Application: Parameters and Settings
No.
A1-02 Control Method Selection
b1-01 Frequency Reference Selection
b6-01 Dwell Reference at Start
b6-02 Dwell Time at Start
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C6-01 Duty Rating
C6-02 Carrier Frequency Selection
d1-01 Frequency Reference 1
d1-02 Frequency Reference 2
d1-03 Frequency Reference 3
E1-03 V/f Pattern Selection
H2-02 Terminals P1 Function Selection (open-collector)
H2-03 Terminals P2 Function Selection (open-collector)
L2-03 Momentary Power Loss Minimum Baseblock Time
L3-04 Momentary Power Loss Voltage Recovery Ramp Time
L4-01 Speed Agreement Detection Level
L4-02 Speed Agreement Detection Width
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L8-05 Input Phase Loss Protection Selection
106
Parameter Name
Parameter Name
Parameter Name
Parameter Name
Parameter Name
Parameter Name
No.
E1-08 Mid Output Frequency Voltage (VC)
E2-01 Motor Rated Current
H1-05 Multi-Function Digital Input Terminal S5 Function Selection
H1-06 Multi-Function Digital Input Terminal S6 Function Selection
H1-07 Multi-Function Digital Input Terminal S7 Function Selection
L5-01 Number of Auto Restart Attempts
0: Open Loop Vector
1: Reverse prohibited
1: Normal Duty
3: 8.0 kHz
39: Watt Hour Pulse Output
2: CPU Power Active - Drive will restart if power returns prior to control power supply shut
down.
4: Derated operation
2: Carrier frequency derating across entire frequency range.
No.
E1-03 V/f Pattern Selection
E1-04 Max Output Frequency (FMAX)
E2-01 Motor Rated Current
H3-11 Terminal A2 Gain Setting
H3-12 Frequency Reference (Current) Terminal A2 Input Bias
L2-01 Momentary Power Loss Operation Selection
L8-03 Overheat Pre-Alarm Operation Selection
o4-12 kWH Monitor Initial Value Selection
0: Open Loop Vector
1: Reverse prohibited
5.0 s
5.0 s
0: Heavy Duty
0FH
1: Enabled
1: Enabled
No.
E1-03 V/f Pattern Selection
E1-07 Mid Output Frequency (FB)
E1-08 Mid Output Frequency Voltage (VC)
E2-01 Motor Rated Current
-
2: Open Loop Vector Control
0: Operator
3.0 Hz
0.3 s
3.0 s
3.0 s
0: Heavy Duty
2: 5 kHz
6.0 Hz
30.0 Hz
60.0 Hz
0FH
37: During frequency output
5: Frequency Detection 2 (FOUT)
0.3 s
0: Disabled
2.0 Hz
0.0 Hz
8: UL3 at RUN - Fault
5%
0.5 s
1: Enabled
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
Parameter Name
Optimum Setting
Parameter Name
Optimum Setting
Parameter Name
-
Optimum Setting