YASKAWA V1000 Series Technical Manual page 368

Index
Permanent Magnet Motor Control, 4
PF, 227, 235
PG Disconnect (for Simple V/f with PG), 227, 227, 236, 241
PGo, 227, 227, 236, 241
PG Open-Circuit Detection Time (for Simple PG V/f Control), 304, 358
Phase Order Selection, 296, 357
PID Accel/Decel Time, 297, 357
PID Adjusted Feedback, 90, 360
PID Control Selection Error, 228
PID Control Selection Fault, 244
PID Differential Feedback, 90
PID Disable, 306
PID Feedback, 90, 218, 309, 322, 360
PID Feedback Fault, 308
PID Feedback High Detection Level, 297, 357
PID Feedback High Level Detection Time, 297, 357
PID Feedback Loss, 227, 227, 231, 239, 308, 308
PID Feedback Loss Detection Level, 297, 357
PID Feedback Loss Detection Time, 297, 357
PID Feedback Reference Missing Detection Selection, 297, 357
PID Function Setting, 297, 357
PID Input (feedback), 90, 218, 322, 360
PID Input Limit, 297
PID Input Switch, 307
PID Integral Hold, 307
PID Integral Reset, 307
PID Offset Adjustment, 297, 357
PID Output, 90, 218, 322, 360
PID output fault, 252
PID Output Gain Setting, 297, 357
PID Output Level Selection, 297, 357
PID Output Limit, 297
PID Output Lower Limit, 297, 357
PID Output Reverse Selection, 297, 357
PID Primary Delay Time Constant, 297, 357
PID Setpoint, 90, 218, 322, 360
PID Set Point, 309
PID Setpoint / User Display, 297, 357
PID Setpoint and Display Digits, 297, 357
PID Setpoint Scaling, 297, 357
PID Setpoint Selection, 297, 357
PID Setpoint Value, 297
PID Sleep Delay Time, 297, 357
PID Sleep Function Start Level, 297, 357
PID Soft Starter, 307
PM Open Loop Vector Control, 68, 75, 81
PM Speed Feedback Detection Suppression Gain, 235
Poor Speed Control Accuracy, 250
Poor Speed Control Accuracy Above Base Speed in Open-loop Vector Motor Control Method,
253
Power Detection Filter Time, 298, 357
Preface, 10
Preferred Parameter Automatic Selection, 97
Preferred Parameters, 97
Previous Fault, 89, 320, 360
Program Lockout, 306
Programming Mode, 61, 62, 62
Proportional Gain Setting (P), 297, 357
Protective Covers, NEMA Type 1, 3
Protective Covers, Open-Chassis, 3
Protective Covers, Reattaching, 40
Protective Covers, Removing, 39, 39
Pull-In Current, 316, 359
Pull-In Current Compensation Time Constant, 235, 253, 316, 359
Pull-In Current during Accel/Decel for PM, 236, 236
Pull-Out Detection, 227, 236
Pulse Train Input Bias, 310, 358
Pulse Train Input Filter Time, 310, 358
Pulse Train Input Gain, 310, 358
Pulse Train Input Scaling, 235, 241, 310, 358
Pulse Train Input , 77
Pulse Train Monitor Scaling, 310, 358
PWM Data Error, 229
368
PWM Data Fault, 226
PWM Feedback Data Fault, 226
PWM Feedback Fault, 230
Q
q-axis ACR Output, 90, 218, 322, 360
R
RAM Fault, 226, 226, 230
Ramp to Stop, 78
Rated Current Setting Alarm, 228, 246
Rated Output Operation, 85
Rated Slip Error, 228, 245
Reference Sample Hold, 306
Regenerative Torque Limit, 309
REMOTE, 4
Replacement Parts, 6, 7, 7, 7
Reset Command Active, 308
Restart Enabled, 308
Reverse Direction, 308
Reverse Jog, 306
Reverse Operation Selection, 296
Reverse Regenerative Torque Limit, 314
Reverse Run Command (2-wire sequence), 307
Reverse Torque Limit, 314, 359
REV Torque Limit, 309
Rotational Auto-Tuning, 91, 93, 210, 211, 249
RTS Control Selection, 310, 358
Run command, 79
Run Command (2-wire sequence 2), 307
Run Command at Power Up, 296, 357
Run Command Input Error, 227
Run Command Input Selection, 4
Run Command Reset, 227
Run Command Selection, 248, 295, 357
Run Command Selection during Program, 296, 357
Run Command Selection Error, 228, 243
Run Command Selection Results, 90, 218, 321
Run Command Source 2, 296, 357
S
S1, 78
S2, 78
Safety Hazard Definitions, 11
Safety Information, 11
S-Curve Characteristic at Accel End, 299, 357
S-Curve Characteristic at Accel Start, 299, 357
S-Curve Characteristic at Decel End, 299, 357
S-Curve Characteristic at Decel Start, 299, 357
S-Curve Characteristics, 81, 225
SE, 227
Search Operation Voltage Limit, 298, 357
SEr, 227, 236
Serial Communication Terminals, 45
Serial Communication Transmission Error, 227, 238
Setup Mode, 62, 4
Shielded Twisted-Pair Cables, 47
Short-Circuit Brake, 308
Short-Circuit Brake (N.C.), 307
Short-Circuit Brake (N.O.), 307
Short Circuit Brake Time at Start, 296, 357
Side-by-Side Setup, 27
Simple V/f with PG, 244
Sinking/Sourcing Mode Switch, 4
Slip Compensation Gain, 224, 299, 357
Slip Compensation Limit, 299, 357
Slip Compensation Primary Delay Time, 299, 357
Slip Compensation Primary Delay Time Constant, 224
Slip Compensation Selection during Regeneration, 299, 357
Soft Charge Circuit Fault, 227
Soft CLA Selection, 314, 359
Soft Starter Speed Reference at Previous Fault, 89, 320, 360
Software No. (Flash), 320, 360
Software No. (ROM), 320, 360
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)