YASKAWA V1000 Series Technical Manual page 362

Index
C2-03, 299, 357
C2-04, 299, 357
C2 S-Curve Characteristics, 299
C3-01, 224, 224, 224
C3-02, 224, 252, 299, 357
C3-03, 250, 250, 299, 357
C3-04, 299, 357
C3-05, 299, 357
C3 Slip Compensation, 299
C4-01, 224, 232, 234, 249
C4-02, 224, 224, 224, 224, 244, 252, 252, 253, 299, 357
C4-03, 299, 357
C4-05, 299, 299, 357, 357
C4-06, 224, 224, 244
C4 Torque Compensation, 299
C5-01, 235, 241
C5-02, 235, 241
C5 Speed Control (ASR), 299
C6-01, 224, 299, 357
C6-02, 53, 224, 224, 233, 233, 234, 251, 251, 251, 252, 254, 254, 299, 357
C6-03, 300, 357
C6-04, 300, 357
C6-05, 252, 300, 357
C6 Carrier Frequency, 299
Cable Length Between Drive and Motor, 43
CALL, 227, 238
Cannot Change Parameter Settings, 6
Capacitor Maintenance, 90, 217, 321
Capacitor Maintenance Setting, 317
Carrier Frequency Lower Limit, 300, 357
Carrier Frequency Proportional Gain, 300, 357
Carrier Frequency Reduction, 314
Carrier Frequency Selection, 224, 224, 299, 357
Carrier Frequency Setting Error, 228, 228, 244
Carrier Frequency Upper Limit, 300, 357
CE, 226, 227, 229, 238
CE Detection Time, 310
CE mark, 348
CF, 226, 229, 229
CI-01, 253
Clock Fault, 226, 226, 230
Coast to Stop, 79
Coast to Stop with Timer, 80
Communication Fault Detection Selection, 310, 358
Communication Parity Selection, 310, 358
Communications ENTER Function Selection, 310, 358
Communication Speed Selection, 310, 358
Communications Test Mode, 307
Connected Machinery Vibrates When Motor Rotates, 251
Constant Torque, 85
Control Circuit Connection Diagram, 44
Control Circuit Fault, 226, 226, 226, 230, 230, 230
Control Circuit Input Terminals, 44
Control Circuit Output Terminals, 45
Control Circuit Terminal Block Configuration, 45
Control Circuit Terminal Block Functions, 3
Control Fault, 226, 229
Control Method Selection, 295, 357
Control Mode, 89, 319, 360
Control Power Supply Undervoltage, 227
Cooling Fan Maintenance Setting (Operation Time), 317, 359
Cooling Fan Operation Time, 90, 217, 321
Cooling Fan Replacement, 6
Copy Allowed Selection, 359
Copy Function Selection, 359
Copy Mode Selection, 359
CPF02, 226, 226, 229
CPF03, 226, 229
CPF06, 229
CPF07, 226, 230
CPF08, 226, 230
CPF11, 226, 230
CPF12, 226, 230
362
CPF13, 226, 230
CPF14, 226, 230
CPF16, 226
CPF17, 226, 230
CPF18, 226, 230
CPF19, 226, 230
CPF20, 226, 230
CPF21, 226, 230
CPF22, 226, 230
CPF23, 226, 230
CPF24, 226, 230
C Tuning, 298
Cumulative Operation Time at 10th Most Recent Fault, 90, 217, 321, 360
Cumulative Operation Time at 2th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 3th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 4th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 5th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 6th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 7th Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at 8th Most Recent Fault, 90, 217, 321, 360
Cumulative Operation Time at 9th Most Recent Fault, 90, 217, 321, 360
Cumulative Operation Time at Most Recent Fault, 90, 217, 320, 360
Cumulative Operation Time at Previous Fault, 89, 320, 360
Current Alarm, 227, 240
Current Alarm Selection, 315, 359
Current Detection Error, 228, 245
Current Fault, 89, 320, 360
Current Offset Fault, 229
Current Unbalance Detection (LF2), 314
D
DC Bus Overvoltage, 241
DC Bus Undervoltage, 237, 308
DC Bus Voltage, 89, 319, 360
DC Bus Voltage at Previous Fault, 89, 320
DC Injection Braking, 251
DC Injection Braking at start, 252
DC Injection Braking at Stop, 252
DC Injection Braking Command, 307
DC Injection Braking Current, 252, 296, 357
DC Injection Braking Current 2, 357
DC Injection Braking Start Frequency, 296, 357
DC Injection Braking Time/DC Excitation Time at Start, 296, 357
DC Injection Braking to Stop, 79
Deceleration Rate Calculation Gain, 312, 359
Deceleration Takes Too Long With Dynamic Braking Enabled, 251
Deceleration Time 1, 80, 298, 357
Deceleration Time 2, 298, 357
Deceleration Time 3 (Motor 2 Decel Time 1), 298, 298, 298, 357, 357
Deceleration Time 4, 298, 357
Deceleration Time at Stall Prevention during Acceleration, 312, 359
Derated Torque, 85
Derivative Time, 297
Differential PID Feedback, 309
Digital Operator Connection Fault, 235
Digital Operator Display Selection, 316, 359
DIP Switch S1, 50
Down 2 Command, 307
Down Command, 306
Drive/kVA Selection, 317, 359
Drive Baseblock, 227
Drive Capacity Setting Fault, 243, 243
Drive Capacity Signal Fault, 226, 230
Drive Cooling Fans, 20
Drive Disabled, 227, 239
Drive Does Not Allow Selection of Rotational Auto-Tuning, 249
Drive Enable, 307, 308
Drive Input Voltage Setting, 4
Drive Intended Use, 3
Drive kVA Setting Error, 227
Drive Mode, 61, 61, 62, 62, 308
Drive Models and Types, 28
Drive Mode Unit Monitor Selection, 316
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)