YASKAWA V1000 Series Technical Manual page 360

D.5 User Setting Table
r1-31 DWEZ Connection Parameter 16 (upr.)
r1-32 DWEZ Connection Parameter 16 (lwr.)
r1-33 DWEZ Connection Parameter 17 (upr.)
r1-34 DWEZ Connection Parameter 17 (lwr.)
r1-35 DWEZ Connection Parameter 18 (upr.)
r1-36 DWEZ Connection Parameter 18 (lwr.)
r1-37 DWEZ Connection Parameter 19 (upr.)
r1-38 DWEZ Connection Parameter 19 (lwr.)
r1-39 DWEZ Connection Parameter 20 (upr.)
r1-40 DWEZ Connection Parameter 20 (lwr.)
T1-00 Motor Selection 1/2
T1-01 Auto-Tuning Mode Selection
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Base Frequency
T1-06 Number of Motor Poles
T1-07 Motor Base Speed
T1-11 Motor Iron Loss
U1-01 Frequency Reference
U1-02 Output Frequency
U1-03 Output Current
U1-04 Control Mode
U1-05 Motor Speed
U1-06 Output Voltage Reference
U1-07 DC Bus Voltage
U1-08 Output Power
U1-09 Torque Reference
U1-10 Input Terminal Status
U1-11 Output Terminal Status
U1-12 Drive Status
U1-13 Terminal A1 Input Voltage
U1-14 Terminal A2 Input Voltage
U1-16 Output Frequency after Soft Start
U1-18 OPE Fault Parameter
U1-19 MEMOBUS/Modbus Error Code
U1-24 Input Pulse Monitor
U1-25 Software No. (Flash)
U1-26 Software No. (ROM)
U2-01 Current Fault
U2-02 Previous Fault
U2-03 Frequency Reference at Previous Fault
U2-04 Output Frequency at Previous Fault
U2-05 Output Current at Previous Fault
U2-06 Motor Speed at Previous Fault
U2-07 Output Voltage at Previous Fault
U2-08 DC Bus Voltage at Previous Fault
U2-09 Output Power at Previous Fault
U2-10 Torque Reference at Previous Fault
U2-11 Input Terminal Status at Previous Fault
U2-12 Output Terminal Status at Previous Fault
U2-13 Drive Operation Status at Previous Fault
U2-14 Cumulative Operation Time at Previous Fault
U2-15 Soft Starter Speed Reference at Previous Fault
U2-16 Motor q-Axis Current at Previous Fault
U2-17 Motor d-Axis Current at Previous Fault
360
U3-01 Most Recent Fault
U3-02 2nd Most Recent Fault
U3-03 3rd Most Recent Fault
U3-04 4th Most Recent Fault
U3-05 5th Most Recent Fault
U3-06 6th Most Recent Fault
U3-07 7th Most Recent Fault
U3-08 8th Most Recent Fault
U3-09 9th Most Recent Fault
U3-10 10th Most Recent Fault
U3-11 Cumulative Operation Time at Most Recent Fault
U3-12 Cumulative Operation Time at 2nd Most Recent Fault
U3-13 Cumulative Operation Time at 3rd Most Recent Fault
U3-14 Cumulative Operation Time at 4th Most Recent Fault
U3-15 Cumulative Operation Time at 5th Most Recent Fault
U3-16 Cumulative Operation Time at 6th Most Recent Fault
U3-17 Cumulative Operation Time at 7th Most Recent Fault
U3-18 Cumulative Operation Time at 8th Most Recent Fault
U3-19 Cumulative Operation Time at 9th Most Recent Fault
U3-20 Cumulative Operation Time at 10th Most Recent Fault
U4-01 Accumulated Operation Time
U4-02 Number of Run Commands
U4-03 Cooling Fan Operation Time
U4-05 Capacitor Maintenance
U4-07 IGBT Maintenance
U4-08 Heatsink Temperature
U4-09 LED Check
U4-10 kWH, Lower 4 Digits
U4-11 kWH, Upper 5 Digits
U4-13 Peak Hold Current
U4-14 Peak Hold Output Frequency
U4-16 Motor Overload Estimate (OL1)
U4-18 Frequency Reference Selection Results
Frequency Reference from MEMOBUS/Modbus
U4-19
Communications
U4-20 Option Frequency Reference
U4-21 Run Command Selection Results
U4-22 MEMOBUS/Modbus Communications Reference
U4-23 Option Card Reference
U5-01 PID Feedback
U5-02 PID Input (feedback)
U5-03 PID Output
U5-04 PID Setpoint
U6-01 Torque Reference (Internal)
U6-02 Motor Secondary Current (Iq)
U6-03 Motor Excitation Current (ld)
U6-04 Output of speed control (ASR) (for Simple V/f PG)
U6-05 Output voltage reference (Vq)
U6-06 Output Voltage Reference (Vd)
U6-07 q-axis ACR Output
U6-08 d-Axis ACR Output
U6-17 Energy Savings Coefficient Calculation Value
U6-18 PID Differential Feedback
U6-19 PID Adjusted Feedback
U6-20 Frequency Reference Bias (Up/Down 2)
U6-21 Offset Frequency
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)