1. Manuals
  2. Brands
  3. YASKAWA Manuals
  4. Controller
  5. V1000 Series
  6. Technical manual

YASKAWA V1000 Series Technical Manual page 307

Compact vector control drive
Hide thumbs Also See for V1000 Series:
Table of Contents

Advertisement

H1-o Setting
Function
20 to 2F
External Fault
30
PID Integral Reset
31
PID Integral Hold
32
Multi-Step Speed Reference 4
34
PID Soft Starter
35
PID Input Switch
40
Forward Run Command (2-wire sequence)
41
Reverse Run Command (2-wire sequence)
42
Run Command (2-wire sequence 2)
43
FWD/REV Command (2-wire sequence 2)
44
Offset Frequency 1 Addition
45
Offset Frequency 2 Addition
46
Offset Frequency 3 Addition
60
DC Injection Braking Command
61
External Search Command 1
62
External Search Command 2
65
KEB Ride-Thru 1 (N.C.)
66
KEB Ride-Thru 1 (N.O.)
67
Communications Test Mode
68
High-Slip Braking
6A
Drive Enable
75
Up 2 Command
76
Down 2 Command
7A
KEB Ride-Thru 2 (N.C.)
7B
KEB Ride-Thru 2 (N.O.)
7C
Short-Circuit Braking (N.O.)
7D
Short-Circuit Braking (N.C.)
7E
Forward/Reverse Detection
9F
DriveWorksEZ enable
No.
Name
H2-01
Terminal MA, MB and MC Function Selection (relay)
H2-02
Terminal P1 Function Selection (open-collector)
H2-03
Terminal P2 Function Selection (open-collector)
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
H1 Multi-Function Digital Input Selections
20: N.O., Always Detected, Ramp To Stop
21: N.C., Always Detected, Ramp To Stop
22: N.O., During Run, Ramp To Stop
23: N.C., During Run, Ramp To Stop
24: N.O., Always Detected, Coast To Stop
25: N.C., Always Detected, Coast To Stop
26: N.O., During Run, Coast To Stop
27: N.C., During Run, Coast To Stop
28: N.O., Always Detected, Fast-stop
29: N.C., Always Detected, Fast-stop
2A: N.O., During Run, Fast-stop
2B: N.C., During Run, Fast-stop
2C: N.O., Always Detected, Alarm Only (continue running)
2D: N.C., Always Detected, Alarm Only (continue running)
2E: N.O., During Run, Alarm Only (continue running)
2F: N.C., During Run, Alarm Only (continue running)
Closed: Resets the PID control integral value.
Closed: Maintains the current PID control integral value.
Used to select Multi-Step Speeds set in d1-01 to d1-16
Closed: Disables the PID soft starter b5-17.
Closed: Inverses the PID input signal
Open: Stop
Closed: Forward run
Note: Can not be set together with Settings 42 or 43.
Open: Stop
Closed: Reverse run
Note: Can not be set together with Settings 42 or 43.
Open: Stop
Closed: Run
Note: Can not be set together with Settings 40 or 41.
Open: Reverse
Closed: Forward
Note: Can not be set together with Settings 40 or 41.
Closed: Adds d7-01 to the frequency reference.
Closed: Adds d7-02 to the frequency reference.
Closed: Adds d7-03 to the frequency reference.
Closed: Triggers DC Injection Braking (b2-02)
Closed: Activates Current Detection Speed Search from the max. output frequency (E1-04) if
b3-01=0. Activates Speed Estimation Type Speed search if b3-01 =1.
Closed: Activates Current Detection Speed Search from the frequency reference b3-01=0.
Activates Speed Estimation Type Speed search if b3-01 =1.
Open: KEB Ride-Thru 1 enabled
Closed: Normal operation
Open: Normal operation
Closed: KEB Ride-Thru 1 enabled
Tests the MEMOBUS/Modbus RS-485/422 interface.
Closed: High-Slip braking is executed. Drive stops.
Open: Drive disabled.
If this input is opened during run, then the drive will stop as specified by parameter b1-03.
Closed: Ready for operation.
Open: Maintains the current frequency reference
Closed: Increases or decreases the frequency reference.
UP 2 and Down 2 commands must be set in combination with each other. The frequency reference
source must be assigned to the operator (b1-01 = "0").
Open: KEB Ride-Thru 2 enabled
Closed: Normal operation
Open: Normal operation
Closed: KEB Ride-Thru 2 enabled
Open: Normal operation
Closed: Short-Circuit Braking
Direction of rotation detection (for Simple V/f w/PG)
Open: DWEZ enabled
Closed: DWEZ disabled
Description
H2: Multi-Function Digital Outputs
Use H2 parameters to assign functions to the multi-function digital outputs.
Refer to H2 Multi-Function Digital Output Settings on page
308
for a description of setting values.
Description
Range
Def.
E
0 to 192
<40>
0
2
B.2 Parameter Table
Control Mode
Pg.
V/f OLV PM
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
-
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
-
-
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
O
O
O
—
-
-
O
—
-
-
O
—
O
-
-
—
O
O
O
—
Control
Mode
Addr.
Pg.
Hex
V/f OL V PM
A
A
A
40B
—
A
A
A
40C
—
A
A
A
40D
—
B
307
Show Quick Links

Hide quick links:

Advertisement

Table of Contents
loading

Related Manuals for YASKAWA V1000 Series

Related Products for YASKAWA V1000 Series

Table of Contents