YASKAWA V1000 Series Technical Manual page 140

5.4 d: Reference Settings
d1-17: Jog Frequency Reference
n
Up to 17 preset references (including Jog Reference) can be set through multi-function inputs S3 to S8.
No.
d1-01 to d1-16
d1-17
Note: The upper limit is determined by the maximum outupt frequency (E1-04) and upper limit for the frequency reference (d2-01).
Detailed Description
To set up 17 separate steps for the speed reference, assign Multi-Step Speed functions to H1-01 to H1-07 (these parameters control the functions set to
terminals S1 to S7).
Note: Terminal S5 needs to be set for Multi-Step Speed 1 (H1-05 = 3), and terminal S6 needs to be set for Multi-Speed Step 2 (H1-06 = 4). To have the drive accelerate as shown
in the Multi-Step Speed operation shown in this section, parameters need to be changed from their default values as described. Because the Jog Frequency is already assigned
to terminal S7 as a default (H1-07 = 6), this setting does not need to be changed.
The drive is defaulted for a 2-step speed operation via the analog input terminals. To enable Multi-Step Speed 1 and 2, set the drive as shown below.
No.
b1-01
H3-10
Procedure
Follow the directions below to set the drive up for Multi-Step Speed operation (allows 17 steps). The example assumes the drive is operating in REMOTE
mode using an analog signal.
Power up the drive. Assign the source of the frequency reference to the LED operator (b1-02 = 1). The run command
1. should already be defaulted to the control circuit terminal (b1-02 = 1). Set multi-function analog input terminal A2
to "Not Used" (H3-10 = F).
2. Set the desired frequencies to d1-01 through d1-16.
3. Set the desired Jog Frequency value to d1-17.
Set multi-function input terminals S3 through S6 for Multi-Step Speed 1 to 4 (H1-03 = 3, H1-04 = 4, H1-05 = 5,
4.
H1-06 = 32).
5.
After setting frequency refrences, press
6.
Press to select REMOTE. The LO/RE light will come on.
The drive will run the motor at the frequencies set to parameters d1-01 through d1-17, selecting each frequency
7. reference according to the switching combination of multi-function input terminals S3 through S7. This allows for
17 separate speed steps (including the Jog Frequency).
Different frequency references can be given to the drive through various switching combinations of multi-function input terminals S3 through S7. Below
is a list of the possible combinations.
d1-01 to d1-17 Multi-StepSpeed
1 OFF
2 ON
3 OFF
4 ON
5 OFF
6 ON
7 OFF
8 ON
9 OFF
10 ON
11 OFF
12 ON
13 OFF
14 ON
15 OFF
16 ON
17 Jog −
*The Jog Frequency overrides whatever frequency reference is being used.
140
Parameter Name
Frequency Reference 1 to 16
Jog Frequency Reference
Parameter Name
Frequency Reference Selection
Terminal A2 Function Selection
Step
to scroll back to the main screen. The
Table 5.3 Multi-Step Speed Reference and Terminal Switch Combinations
Multi-StepSpeed 2 Multi-StepSpeed 3
OFF OFF
OFF OFF
ON OFF
ON OFF
OFF ON
OFF ON
ON ON
ON ON
OFF OFF
OFF OFF
ON OFF
ON OFF
OFF ON
OFF ON
ON ON
ON ON
− −
Setting Range
0.00 to 400.00
0.00 to 400.00
Setting Range
0 to 4
0 to 31
⇒
⇒
LED should light.
⇒
⇒
Multi-StepSpeed 4 Jog Reference
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
− ON
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
Default
* 0.00 Hz
* 6.00 Hz
Default Page
1 −
0 −
Display/Result
STOP
STOP
Reference
Frequency Reference 1 (d1-01)
Frequency Reference 2 (d1-02)
Frequency Reference 3 (d1-03)
Frequency Reference 4 (d1-04)
Frequency Reference 5 (d1-05)
Frequency Reference 6 (d1-06)
Frequency Reference 7 (d1-07)
Frequency Reference 8 (d1-08)
Frequency Reference 9 (d1-09)
Frequency Reference 10 (d1-10)
Frequency Reference 11 (d1-11)
Frequency Reference 12 (d1-12)
Frequency Reference 13 (d1-13)
Frequency Reference 14 (d1-14)
Frequency Reference 15 (d1-15)
Frequency Reference 16 (d1-16)
Jog Frequency Reference (d1-17) *