YASKAWA V1000 Series Technical Manual page 364

Index
E2-01, 354
Energy Saving Gain, 357
European Standards, 14
Fast-stop Time, 357
Forward Regenerative Torque Limit, 359
Frequency Reference at Reference Loss, 359
Frequency Reference Loss Detection Selection, 359
Heavy Load Current Level (for PM), 359
High-Slip Braking Current Limit, 359
High-Slip Braking Overload Time, 359
Hunting Prevention Gain Setting, 359
Hunting Prevention Selection, 359
Hunting Prevention Time Constant, 359
Jump Frequency 1, 357
Jump Frequency 2, 357
Jump Frequency 3, 357
L1-01, 354
L1-02, 355
Low Voltage Wiring, 354
Main Circuit Terminal Wiring, 353
Main Power Circuit Voltage Adjustment Gain, 359
Max Voltage (VMAX), 358
Memobus/Modbus Error Code, 360
Momentary Power Loss Minimum Baseblock Time, 358
Momentary Power Loss Operation Selection, 358
Motor 2 Iron Loss, 358
Motor 2 Rated Slip, 358
Motor Acceleration Time for Inertia Calculations, 359
Motor Excitation Current (ld), 360
Motor Overload Estimate (OL1), 360
Motor Overload Protection Selection, 354
Motor Overload Protection Time, 355
Motor Rated Current, 354
Motor Rated Output, 358
Motor Rated Slip, 358
Motor Secondary Current (Iq), 360
Motor Speed at Previous Fault, 360
Motor Temperature Input Filter Time (PTC input), 358
Offset Frequency, 360
Offset Frequency 1, 358
Offset Frequency 2, 358
Offset Frequency 3, 358
Option Frequency Reference, 360
Output Current at Previous Fault, 360
Output Frequency after Soft Start, 360
Output Phase Loss Protection, 359
Output Power at Previous Fault, 360
Output Voltage at Previous Fault, 360
Output Voltage Reference (Vd), 360
Output voltage reference (Vq), 360
Overexcitation Deceleration Gain, 359
Password 2, 357
Peak Hold Output Frequency, 360
PID Differential Feedback, 360
PID Input Limit, 357
PID Output Limit, 357
PID Setpoint Value, 357
Reverse Regenerative Torque Limit, 359
Run Command Selection Results, 360
Stall Prevention Selection during Deceleration, 359
STOP Key Function Selection, 359
Terminal A1 Input Voltage, 360
Terminal A2 Input Voltage, 360
Torque Detection Selection 2, 359
Torque Reference (Internal), 360
U2, U3 Initial Value Selection, 359
UL Standards, 14
User Parameter Default Value, 359
F
F1-02, 304, 358
F1-03, 304, 358
F1-04, 304, 358
364
F1-08, 235, 241, 304, 358
F1-08 and F1-09, 235
F1-09, 241, 304, 358
F1-10, 231, 238, 239, 304, 358
F1-10 and F1-11, 231
F1-11, 231, 238, 239, 304, 358
F1-14, 236, 241, 304, 358
F1 Simple PG V/f Parameters, 304
F6-03, 231, 239
F6 and F7 Serial Communications Option Card Settings, 305
FA, 84
Fast-stop (N.C.), 306
Fast-Stop (N.O.), 306
Fast-stop Time, 298
Fault, 308
Fault Causes and Solutions, 229
Fault Detection, 229
Fault Displays, 229
Fault History, 247, 247
Fault Reset, 306
Fault Reset Example, 6
Fault Reset Interval Time, 313, 359
Fault Reset Operation Selection, 313, 359
Fault Reset when Run Command Entered, 241
Faults, 226, 226
Fault Trace Example, 6
FB, 84
FbH, 227, 227, 231, 239
FbL, 227, 227, 231, 239
Feedback Detection Control Time Constant 2, 250
FJOG/RJOG, 4
FLASH memory error, 230
FLASH Memory Fault, 226, 226, 230
FMAX, 84
FMIN, 84
Forward/Reverse Run Command Input Error, 239
Forward Jog, 306
Forward Regenerative Torque Limit, 314
Forward Run Command (2-wire sequence), 307
Forward Torque Limit, 314, 359
Fref/Fout Agree 1, 308
Fref/Fout Agree 2, 308
Fref/Fset Agree 1, 308
Fref/Fset Agree 2, 308
Frequency (FOUT) Detection 1, 308
Frequency (FOUT) Detection 2, 308
Frequency Bias (A1), 309
Frequency Detection 3, 308
Frequency Detection 4, 308
Frequency Gain, 309
Frequency Reduction Rate during OH Pre-Alarm, 314, 359
Frequency Reference, 89, 318, 360
Frequency Reference (Current) Terminal A2 Input Bias, 309, 358
Frequency Reference 1, 98, 300, 357
Frequency Reference 10, 300, 357
Frequency Reference 11, 300, 357
Frequency Reference 13, 300, 357
Frequency Reference 14, 300, 357
Frequency Reference 15, 300, 357
Frequency Reference 16, 300, 357
Frequency Reference 2, 98, 251, 296, 300, 357, 357
Frequency Reference 3, 98, 300, 357
Frequency Reference 4, 98, 300, 357
Frequency Reference 5, 300, 357
Frequency Reference 6, 300, 357
Frequency Reference 7, 300, 357
Frequency Reference 8, 300, 357
Frequency Reference 9, 300, 357
Frequency Reference Accel/Decel (Up/Down 2), 301, 358
Frequency Reference at Previous Fault, 89, 320, 360
Frequency Reference at Reference Loss, 312
Frequency Reference Bias (Up/Down 2), 90, 218, 301, 322, 358, 360
Frequency Reference Bias Operation Mode Selection (Up/Down 2), 301, 358
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)