Parameters: 15-** Drive Information - Danfoss VLT AutomationDrive FC 301 Programming Manual

Parameter Descriptions

3.16 Parameters: 15-** Drive Information

3.16.1 15-0* Operating Data
15-00 Operating hours
3 3
Range:
0 h [0 - 2147483647 h] View how many hours the frequency
*
15-01 Running Hours
Range:
0 h [0 -
*
2147483647 h]
15-02 kWh Counter
Range:
0 kWh [0 -
*
2147483647
kWh]
15-03 Power Up's
Range:
0 [0 - 2147483647 ] View the number of times the frequency
*
15-04 Over Temp's
Range:
0 [0 - 65535 ] View the number of frequency converter
*
15-05 Over Volt's
Range:
0 [0 - 65535 ] View the number of frequency converter
*
15-06 Reset kWh Counter
Option:
[0] Do not reset
*
[1] Reset counter Press [OK] to reset the kWh counter to 0
15-07 Reset Running Hours Counter
Option:
[0] Do not
*
reset
[1] Reset
counter
168
VLT
Function:
converter has run. The value is saved
when the frequency converter is
turned off.
Function:
View how many hours the motor has run.
Reset the counter in
parameter 15-07 Reset Running Hours
Counter. The value is saved when the
frequency converter is turned off.
Function:
Registers the power consumption of
the motor as an average value over 1
hour. Reset the counter in
parameter 15-06 Reset kWh Counter.
Function:
converter has been powered up.
Function:
temperature faults.
Function:
overvoltages.
Function:
No reset of the kWh counter is required.
(see parameter 15-02 kWh Counter).
Function:
To reset the running hours counter to 0, select
[1] Reset and press [OK] (see
parameter 15-01 Running Hours). This
Danfoss A/S © 02/2016 All rights reserved.
®
AutomationDrive FC 301/302
15-07 Reset Running Hours Counter
Option:
3.16.2 15-1* Data Log Settings
The data log enables continuous logging of up to 4 data
sources (parameter 15-10 Logging Source) at individual rates
(parameter 15-11 Logging Interval). A trigger event
(parameter 15-12 Trigger Event) and window
(parameter 15-14 Samples Before Trigger) are used to start
and stop the logging conditionally.
15-10 Logging Source
Option:
[0] None
*
[15] Readout: actual setup
[1472] Legacy Alarm Word
[1473] Legacy Warning Word
[1474] Leg. Ext. Status Word
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference %
[1603] Status Word
[1606] Actual Position
[1607] Target Position
[1608] Position Error
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor current
[1616] Torque [Nm]
[1617] Speed [RPM]
[1618] Motor Thermal
[1620] Motor Angle
[1621] Torque [%] High Res.
[1622] Torque [%]
[1624] Calibrated Stator Resistance
[1625] Torque [Nm] High
[1630] DC Link Voltage
[1632] Brake Energy /s
[1633] Brake Energy Average
[1634] Heatsink Temp.
[1635] Inverter Thermal
[1644] Speed Error [RPM]
[1648] Speed Ref. After Ramp [RPM]
[1650] External Reference
[1651] Pulse Reference
Function:
parameter cannot be selected via the serial
port, RS485.
Select [0] Do not reset if no reset of the
running-hours counter is required.
Function:
Select which variables
are to be logged.
MG33ML02