Danfoss VLT AutomationDrive FC 301 Programming Manual page 208

Parameter Lists
Password Protection of Safety
0-69 Parameters
4.1.5 1-** Load/Motor
Par- Parameter description
ameter #
1-0* General Settings
4 4
1-00 Configuration Mode
1-01 Motor Control Principle
1-02 Flux Motor Feedback Source
1-03 Torque Characteristics
1-04 Overload Mode
1-05 Local Mode Configuration
1-06 Clockwise Direction
1-07 Motor Angle Offset Adjust
1-1* Special Settings
1-10 Motor Construction
1-11 Motor Model
1-18 Min. Current at No Load
1-2* Motor Data
1-20 Motor Power [kW]
1-21 Motor Power [HP]
1-22 Motor Voltage
1-23 Motor Frequency
1-24 Motor Current
1-25 Motor Nominal Speed
1-26 Motor Cont. Rated Torque
1-29 Automatic Motor Adaptation (AMA)
1-3* Adv. Motor Data
1-30 Stator Resistance (Rs)
1-31 Rotor Resistance (Rr)
1-33 Stator Leakage Reactance (X1)
1-34 Rotor Leakage Reactance (X2)
1-35 Main Reactance (Xh)
1-36 Iron Loss Resistance (Rfe)
1-37 d-axis Inductance (Ld)
1-39 Motor Poles
1-40 Back EMF at 1000 RPM
1-41 Motor Angle Offset
1-46 Position Detection Gain
1-47 Torque Calibration
1-5* Load Indep. Setting
1-50 Motor Magnetisation at Zero Speed
Min Speed Normal Magnetising
1-51 [RPM]
1-52 Min Speed Normal Magnetising [Hz]
1-53 Model Shift Frequency
1-54 Voltage reduction in fieldweakening
1-55 U/f Characteristic - U
1-56 U/f Characteristic - F
1-57 Torque Estimation Time Constant
1-58 Flying Start Test Pulses Current
206
®
VLT AutomationDrive FC 301/302
[0] Disabled 1 set-up
Default value 4 set-up
ExpressionLimit All set-ups
ExpressionLimit All set-ups
[1] 24V encoder All set-ups
[0] Constant torque All set-ups
[0] High torque All set-ups
[2] As mode par
1-00 All set-ups
[0] Normal All set-ups
[0] Manual All set-ups
[0] Asynchron All set-ups
ExpressionLimit All set-ups
0 % All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
[0] Off All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
0 N/A All set-ups
100 % All set-ups
ExpressionLimit All set-ups
100 % All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
0 V All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
150 ms All set-ups
ExpressionLimit All set-ups
Danfoss A/S © 02/2016 All rights reserved.
TRUE –
Change during Conversion
operation index
TRUE –
FALSE –
FALSE –
TRUE –
FALSE –
TRUE –
FALSE –
FALSE –
FALSE –
FALSE –
TRUE 0
FALSE 1
FALSE -2
FALSE 0
FALSE 0
FALSE -2
FALSE 67
FALSE -1
FALSE –
FALSE -4
FALSE -4
FALSE -4
FALSE -4
FALSE -4
FALSE -3
FALSE -4
FALSE 0
FALSE 0
TRUE 0
TRUE 0
TRUE –
TRUE 0
TRUE 67
TRUE -1
FALSE -1
FALSE 0
TRUE -1
TRUE -1
TRUE -3
FALSE 0
Uint8
Type
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint8
Uint16
Uint32
Uint32
Uint16
Uint16
Uint32
Uint16
Uint32
Uint8
Uint32
Uint32
Uint32
Uint32
Uint32
Uint32
Int32
Uint8
Uint16
Int16
Uint16
Uint8
Uint16
Uint16
Uint16
Uint16
Uint8
Uint16
Uint16
Uint16
Uint16
MG33ML02