Danfoss VLT AutomationDrive FC 301 Programming Manual page 98

Parameter Descriptions
NOTICE
Options [4] PTC 1 Alarm to [9] PTC 1 & Relay W/A are only
available when the MCB 112 is connected.
NOTICE
3 3
Selecting Auto Reset/Warning enables automatic restart
of the frequency converter.
Function
No Function
Safe Torque Off
Alarm
Safe Torque Off
Warning
PTC 1 Alarm
PTC 1 Warning
PTC 1 & Relay A
PTC 1 & Relay W
PTC 1 & Relay A/W
PTC 1 & Relay W/A
Table 3.19 Overview of Functions, Alarms, and Warnings
W means warning and A means alarm. For further information, see
Alarms and Warnings in the Troubleshooting section in the Design
Guide or the Operating Instructions.
A dangerous failure related to Safe Torque Off issues alarm
72, Dangerous Failure.
Refer to Table 5.1.
5-20 Terminal X46/1 Digital Input
Option:
[0] No operation This parameter is active when option module
*
5-21 Terminal X46/3 Digital Input
Option:
[0] No operation This parameter is active when option module
*
96
®
VLT
Num PTC Relay
ber
[0] – –
[1]* – Safe Torque Off
[A68]
[3] – Safe Torque Off
[W68]
[4] PTC 1 Safe Torque –
Off [A71]
[5] PTC 1 Safe Torque –
Off [W71]
[6] PTC 1 Safe Torque Safe Torque Off
Off [A71] [A68]
[7] PTC 1 Safe Torque Safe Torque Off
Off [W71] [W68]
[8] PTC 1 Safe Torque Safe Torque Off
Off [A71] [W68]
[9] PTC 1 Safe Torque Safe Torque Off
Off [W71] [A68]
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Danfoss A/S © 02/2016 All rights reserved.
AutomationDrive FC 301/302
5-22 Terminal X46/5 Digital Input
Option:
[0] No operation This parameter is active when option module
*
5-23 Terminal X46/7 Digital Input
Option:
[0] No operation This parameter is active when option module
*
5-24 Terminal X46/9 Digital Input
Option:
[0] No operation This parameter is active when option module
*
5-25 Terminal X46/11 Digital Input
Option:
[0] No operation This parameter is active when option module
*
5-26 Terminal X46/13 Digital Input
Option:
[0] No operation This parameter is active when option module
*
3.7.3 5-3* Digital Outputs
The 2 solid-state digital outputs are common for terminals
27 and 29. Set the I/O function for terminal 27 in
parameter 5-01 Terminal 27 Mode, and set the I/O function
for terminal 29 in parameter 5-02 Terminal 29 Mode.
NOTICE
These parameters cannot be adjusted while the motor
runs.
[0] No operation
[1] Control ready
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Function:
®
VLT Extended Relay Card MCB 113 is
installed in the frequency converter.
Functions are described under parameter
group 5-1* Digital Inputs.
Default for all digital outputs and relay
outputs.
The control card is ready, for example:
Feedback from a frequency converter
MG33ML02