JLG 400S Service And Maintenance Manual page 495

Help Message DTC
FUNCTION SWITCHES LOCKED - 2223
SELECTED BEFORE ENABLE
FOOTSWITCH SELECTED 2224
BEFORE START
FUNCTION PROBLEM - PLAT- 2247
FORM ROTATE LEFT PERMA-
NENTLY SELECTED
FUNCTION PROBLEM - PLAT- 2248
FORM ROTATE RIGHT PERMA-
NENTLY SELECTED
FUNCTION PROBLEM - JIB LIFT 2249
UP PERMANENTLY SELECTED
FUNCTION PROBLEM - JIB LIFT 2250
DOWN PERMANENTLY
SELECTED
FUNCTION PROBLEM - TELE- 2251
SCOPE IN PERMANENTLY
SELECTED
FUNCTION PROBLEM - TELE- 2252
SCOPE OUT PERMANENTLY
SELECTED
FUNCTION PROBLEM - TOWER 2257
LIFT UP PERMANENTLY
SELECTED
FUNCTION PROBLEM - TOWER 2258
LIFT DOWN PERMANENTLY
SELECTED
FUNCTION PROBLEM - PLAT- 2262
FORM LEVEL UP PERMANENTLY
SELECTED
FUNCTION PROBLEM - PLAT- 2263
FORM LEVEL DOWN PERMA-
NENTLY SELECTED
3121671
Table 6-11. Diagnostic Trouble Code Chart
Fault Condition/Trigger
(For configurable items, fault applies only if
configured. All listed conditions to be met
unless stated otherwise)
Machine is in Platform Mode;
Any of the following Platform inputs are active when
Footswitch becomes active or while DTC 2212, 2213 or
2221 is active:
Tower Lift;
Telescope;
Platform Level;
Platform Rotate;
Jib Lift (if MACHINE SETUP > JIB = YES)
Machine is in Platform Mode;
The engine is stopped;
Startup time has expired;
The Footswitch is active before the Platform Engine
Start switch input = High
Machine is in Platform Mode;
The Platform Rotate Left switch input = High at Startup
Machine is in Platform Mode;
The Platform Rotate Right switch input = High at
Startup
Machine is in Platform Mode;
MACHINE SETUP > JIB = YES;
The Jib Lift Up switch input = High at Startup
Machine is in Platform Mode;
MACHINE SETUP > JIB = YES;
The Jib Lift Down switch input = High at Startup
Machine is in Platform Mode;
The Telescope In switch input = High at Startup
Machine is in Platform Mode;
The Telescope Out switch input = High at Startup
Machine is in Platform Mode;
The Tower Lift Up switch input = High at Startup
Machine is in Platform Mode;
The Tower Lift Down switch input = High at Startup
Machine is in Platform Mode;
The Platform Level Up switch input = High at Startup
Machine is in Platform Mode;
The Platform Level Down switch input = High at
Startup
SECTION 6 - JLG CONTROL SYSTEM
Required Control
Conditions Required for Movement
Response or State
and/or to Clear Fault
Assignment
The UGM shall not Enable Controls initialized
the Machine
The UGM shall prohibit The Platform Engine Start switch input =
Engine Start Low;
The UGM shall prohibit The Platform Rotate Left switch input =
Platform Rotate Left and Low;
Right Platform Rotate Left and Right permitted
after controls are initialized
The UGM shall prohibit The Platform Rotate Right switch input =
Platform Rotate Left and Low;
Right Platform Rotate Left and Right permitted
after controls are initialized
The UGM shall prohibit Jib The Jib Lift Up switch input = Low;
Lift Up and Down Jib Lift Up and Down permitted after con-
trols are initialized
The UGM shall prohibit Jib The Jib Lift Down switch input = Low;
Lift Up and Down Jib Lift Up and Down permitted after con-
trols are initialized
The UGM shall prohibit The Telescope In switch input = Low;
Telescope In and Out Telescope permitted after controls are ini-
tialized
The UGM shall prohibit The Telescope Out switch input = Low;
Telescope In and Out Telescope permitted after controls are ini-
tialized
The UGM shall prohibit The Tower Lift In switch input = Low;
Tower Lift Up and Down Tower Lift Up and Down permitted after
controls are initialized
The UGM shall prohibit The Tower Lift Down switch input = Low;
Tower Lift Up and Down Tower Lift Up and Down permitted after
controls are initialized
The UGM shall prohibit The Platform Level Up switch input = Low;
Platform Level Up and Platform Level Up and Down permitted
Down after controls are initialized
The UGM shall prohibit The Platform Level Down switch input =
Platform Level Up and Low;
Down Platform Level Up and Down permitted
after controls are initialized
X X
X X
X X
X X
X X
X X
X X
X X
X
X
X X
X X
6-55