Subscribe to Our Youtube Channel
Related Manuals for JLG 4108AN
Summary of Contents for JLG 4108AN
- Page 1 Operation and Safety Manual Models 4108AN 1730895 August 06, 2018 ISO 9001 Lic 6080...
- Page 2 Take time to read this book thoroughly. If you are uncertain about any of the information presented, contact your JLG Service Office before operations commence. All instructions in this manual are based on the machine being used under the operating conditions for which it was designed.
- Page 3 Kewdale, Perth Eagle Farm, Brisbane WA 6105 QLD 4009 Phone: (08) 9356 9811 Phone: (07) 3309 9111 JLG Industries (NSW) JLG Industries (SA) 8 Nucera 358 Park Road Court Greenfields, Adelaide Regents Park, Sydney SA 5107 NSW 2143 Phone: (08) 82598777...
-
Page 4: Table Of Contents
4108AN SECTION ONE OPERATORS AND SAFETY MANUAL CONTENTS Page General Safety alert symbols Safety precautions Preparation for use Delivery and periodic inspection Controls identification Machine set up/pack up instructions. Forklifting machine 1-11 Craning machine 1-11 Towing Instructions 1-12... -
Page 5: General
If there is a question on application and/or operation, JLG Industries Customer Support Department should be consulted on (02) 6581 1111 (Australia). -
Page 6: Safety Alert Symbols
4108AN SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS This is the Safety Alert Symbol. It is used to alert you to the potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. -
Page 7: Safety Precautions
4108AN SAFETY PRECAUTIONS Prior to erecting the mast the SAFETY PRECAUTIONS operator should ensure that no overhead obstructions are within a This section outlines the safety 6-metre radius of the base of the precautions applicable to the general machine. use of this product. - Page 8 FRONT OF THE MACHINE NEAR THE BASE OF THE MAST TO AID IN LEVELLING OF THE MACHINE. The model 4108AN Lighting Tower incorporates an A.C. alternator which generates lethal voltages. Do NOT operate the machine without all safety covers in place covering all wiring and electrical devices.
-
Page 9: Preparation For Use
4108AN PREPARATION FOR USE PREPARATION FOR USE DELIVERY AND PERIODIC INSPECTION Before a new machine is put into operation it must be carefully inspected for any evidence of damage resulting This machine requires periodic safety from shipment. and maintenance inspections by a qualified person. -
Page 10: Controls Identification
4108AN CONTROLS IDENTIFICATION CONTROLS IDENTIFICATION 1. Mast raise and lower control lever. Pushing forward or pulling back will Engine Control Panel raise and lower the mast respectively. Speed of the raise and lower function can be controlled by pushing or pulling the lever further away from the centre off position. - Page 11 4108AN CONTROLS IDENTIFICATION rotated clockwise to lock mast prior to use. 3. Mast rotate lockpin. This pin is spring loaded into the locked position. It must be pulled out prior to rotating mast. The pin locks the mast every 15 degrees. The mast...
-
Page 12: Machine Set Up/Pack Up Instructions
4108AN MACHINE SET UP AND PACK UP support jack is pressing firmly MACHINE SET UP AND PACK UP against the ground. Located behind INSTRUCTIONS the flip up number plate is a fourth outrigger leg. Release the remote locking pin and flip up the number plate. - Page 13 4108AN MACHINE SET UP AND PACK UP Once started, allow the engine to warm for a minute prior to using. THE NEXT STEPS REFER TO RAISING THE MAST. CHECK 14. Switch on main circuit breaker to ENSURE THAT switch on the lights.
- Page 14 4108AN MACHINE SET UP AND PACK UP Machine Pack Up To pack up the machine ready for towing or transport, reverse the above steps. Take special care when lowering the boom and ensure it rests neatly in the boom cradle at the rear of the machine.
-
Page 15: Forklifting Machine
4108AN LIFTING MACHINE FORKLIFTING MACHINE CRANING MACHINE Forklifting Procedure Craning Procedure WHEN USING A FORKLIFT TO USE ONLY THE 4 LIFTING POINTS MOVE THE MACHINE ONLY THE PROVIDED TO LIFT THE LIGHTING FORKLIFT POCKETS LOCATED AT TOWER WITH A CRANE. DO NOT... -
Page 16: Towing Instructions
4108AN TOWING INSTRUCTIONS x Swing the front jack up into the horizontal stowed position. x Ensure that the overriding brake PRIOR TO TOWING THE LIGHT lockout lever is swung up to allow TOWER UNIT THIS MANUAL brakes to work. SHOULD...
Need help?
Do you have a question about the 4108AN and is the answer not in the manual?
Questions and answers