Data Interfaces - HEIDENHAIN TNC 415 Technical Manual

D
D ............................................................... 8-18
D= (ASSIGN DOUBLE) ........................... 7-45
Damping factor ......................................... 4-76
DATA CARRIER @\: IS FULL .................... 8-50
DATA CARRIER EMPTY ........................... 8-49
DATA CARRIER MISSING........................ 8-49
DATA CARRIER
WRITE-PROTECTED........................ 8-48; 8-49
Data interface ......................... 3-40; 7-162; 8-3
Data lines.................................................. 8-11
DATA MEDIUM EMPTY ........................... 8-48
DATA MEDIUM MISSING........................ 8-48
Data transfer............................................... 8-4
Data transfer NC/PLC ............................... 7-19
Data transfer rate ....................................... 8-8
Datum................................. 4-17; 4-126; 4-221
Datum....................................................... 2-15
Datum point.............................................. 4-53
Datum setting........................................... 4-52
Datum shift............................................. 4-132
Datum table ........................ 4-151; 7-157; 8-18
Datum-table ............................................ 4-150
DC1............................................................. 8-9
DC3............................................................. 8-9
Decimal sign ........................................... 4-154
DEF-active .................................................. 9-3
Deflection depth ..................................... 4-190
Dialog file.................................................... 9-7
Dialog language .......................................... 2-7
Dialog language ........................................ 2-15
Dialog numbers .......................................... 9-3
Dialogue language .................................. 4-153
Dialogues for user-parameters ............... 4-152
Digital speed control................................. 11-2
Digitising..................................................... 2-8
Digitising................................................... 2-14
Digitising with the TM 110 ..................... 4-189
Digitizing ..................................................... 2-6
Digitizing with TS 120............................. 4-180
Direction of traverse ................................. 4-9
Direction of spindle rotation ..................... 4-95
Direction of traverse ............... 4-8; 4-62; 4-263
Direction of traverse ................................... 4-8
Display .................................................... 4-126
Display step ............................................ 4-134
Distance-coded reference marks .... 3-24; 4-52
DIVISION (/) ............................................ 7-69
DIVISION [ ] (/[ ]) ..................................... 7-85
DLG-CALL................................................... 9-3
DLG-DEF..................................................... 9-3
DNC .......................................................... 8-46
DNC operation .......................................... 8-19
Double swivel head .................................. 4-43
13-4 TNC 407/TNC 415
Doubleword ..................................... 7-16; 7-18
Dwell-time .............................................. 4-114
E
Earthing plan ............................................. 3-20
Edge evaluation ........................................ 7-27
Edge separation of the measuring
system signals .......................................... 4-10
Editor program ............................................ 7-7
Electrical interference ................................. 3-9
Electrical noise immunity............................ 3-9
EMERGENCY STOP routine ................... 4-262
EMERGENCY STOP-routine ................... 4-120
End of Module ........................................ 7-110
End of program ....................................... 4-154
ENDC (ENDCASE) ................................. 7-130
Entry error................................................... 5-4
Entry format................................................ 5-3
EPROM..................................................... 2-11
EPROM creation ....................................... 7-10
EPROM sockets ....................................... 2-11
EPROM-creation ....................................... 7-28
EQUAL TO (==) ........................... 7-73; 7-119
EQUAL TO [ ] (==[ ]) ............................... 7-89
ERR........................................................... 8-49
Error compensation .................................... 2-5
Error in PLC program 1R.................. 2-17; 2-19
Error in PLC-program .............................. 4-174
ERROR IN PLC-PROGRAM .................... 4-209
Error in PLC-program 1Q .......................... 4-95
Error message ................ 4-9; 4-18; 4-77; 4-84;
............... 4-85; 4-86; 4-87; 4-102; 4-120; 4-174
Error messages......................................... 8-48
ERROR NUMBER ..................................... 8-29
ERROR= ..................................................... 9-5
Error-message .......................................... 7-30
EXCLUSIVE OR (XO)............................... 7-61
EXCLUSIVE OR [ ] (XO[ ])........................ 7-81
EXCLUSIVE OR NOT (XON) ................... 7-63
EXCLUSIVE OR NOT [ ] (XON[ ]) ............ 7-81
EXE ............................................................. 4-7
Executable program.................................... 7-7
Export version...................................... 2-7; 3-4
Export versions ........................................... 2-6
EXT. OUTPUT/INPUT NOT READY .......... 8-48
EXT1/EXT2/EXT3....................................... 8-19
EXTERN Instruction ................................ 7-133
External EMERGENCY STOP ................. 4-120
Subject Index 01.98