YASKAWA L1000A Technical Manual page 507

No.
H5-02 Communication Speed Selection
H5-03 Communication Parity Selection
H5-04 Stopping Method After Communication Error (CE)
H5-05 Communication Fault Detection Selection
H5-06 Drive Transmit Wait Time
H5-07 RTS Control Selection
H5-09 Communication Fault Detection Time
H5-10 Unit Selection for MEMOBUS/Modbus Register 0025H
H5-11 Communications ENTER Function Selection
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
Motor Overheat Alarm Operation Selection
L1-03
(PTC thermistor input)
Motor Overheat Fault Operation Selection
L1-04
(PTC thermistor input)
Motor Temperature Input Filter Time
L1-05
(PTC thermistor input)
L1-13 Continuous Electrothermal Operation Selection
L2-05 Undervoltage Detection Level (Uv)
L3-01 Stall Prevention Selection during Acceleration
L3-02 Stall Prevention Level during Acceleration
L3-05 Stall Prevention Selection during Run
L3-06 Stall Prevention Level during Run
L4-01 Speed Agreement Detection Level
L4-02 Speed Agreement Detection Width
L4-03 Speed Agreement Detection Level (+/-)
L4-04 Speed Agreement Detection Width (+/-)
L4-05 Speed Reference Loss Detection Selection
L4-06 Speed Reference at Reference Loss
L4-07 Speed Agree Detection Selection
L4-13 Door Zone Level
L5-01 Number of Auto Reset Attempts
L5-02 Fault Output Operation during Auto Reset
L5-06 Undervoltage Fault Reset Selection
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L6-04 Torque Detection Selection 2
L6-05 Torque Detection Level 2
L6-06 Torque Detection Time 2
L7-01 Forward Torque Limit
L7-02 Reverse Torque Limit
L7-03 Forward Regenerative Torque Limit
L7-04 Reverse Regenerative Torque Limit
L7-16 Torque Limit Process at Start
L8-02 Overheat Alarm Level
L8-03 Overheat Pre-Alarm Operation Selection
L8-05 Input Phase Loss Protection Selection
L8-06 Input Phase Loss Detection Level
L8-07 Output Phase Loss Protection Selection
L8-09 Output Ground Fault Detection Selection
L8-10 Heatsink Cooling Fan Operation Selection
L8-11 Heatsink Cooling Fan Off Delay Time
L8-12 Ambient Temperature Setting
L8-15 oL2 Characteristics Selection at Low Speeds
L8-27 Overcurrent Detection Gain
L8-29 Current Unbalance Detection (LF2)
L8-35 Installation Selection
L8-38 Automatic Torque Boost Selection
L8-39 Reduced Carrier Frequency
L8-55 Internal Braking Transistor Protection
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
User
Name
Setting
No. Name
L8-62 Operation Selection at Input Phase Loss
L8-77 Oscillation Suppression
L8-88 Safe Disable Operation Mode
L8-89 Current Monitoring Selection
L8-99 Current Monitoring Level
n1-08 Leakage Current Vibration Control Selection
n2-01 Speed Feedback Detection Control (AFR) Gain
n2-02 Speed Feedback Detection Control (AFR) Time Constant 1
n2-03 Speed Feedback Detection Control (AFR) Time Constant 2
n5-01 Inertia Compensation Selection
n5-02 Motor Acceleration Time
n5-03 Inertia Compensation Gain
n5-07 Speed Feedback Compensation Selection
n5-08 Speed Feedback Compensation Gain (P)
n6-01 Online Tuning Selection
n6-05 Online Tuning Gain
n8-01 Initial Polarity Estimation Current
n8-02 Pole Attraction Current
n8-29 q-Axis Current Control Gain during Normal Operation
q-Axis Current Control Integral Time during Normal
n8-30
Operation
n8-32 d-Axis Current Control Gain during Normal Operation
d-Axis Current Control Integral Time during Normal
n8-33
Operation
n8-35 Initial Rotor Position Detection Selection
n8-36 High Frequency Injection Level
n8-37 High Frequency Injection Amplitude
n8-62 Output Voltage Limit
n8-81 High Frequency Injection during Rescue Operation
High Frequency Injection Amplitude during Rescue
n8-82
Operation
n8-84 Polarity Detection Current
n8-86 Magnet Pole Search Error Detection Selection
n9-60 A/D Conversion Start Delay
o1-01  Drive Mode Unit Monitor Selection
o1-02  User Monitor Selection After Power Up
o1-03 Digital Operator Display Unit Selection
o1-04 V/f Pattern Setting Units
o1-05  LCD Contrast Control
o1-06 User Monitor Selection Mode
o1-07 Second Line Monitor Selection
o1-08 Third Line Monitor Selection
o1-10 User-Set Display Units Maximum Value
o1-11 User-Set Display Units Decimal Display
o1-12 Length Units
o1-20 Traction Sheave Diameter
o1-21 Roping Ratio
o1-22 Mechanical Gear Ratio
o1-23 HBB Non Display Select
o2-01 LO/RE Key Function Selection
o2-02 STOP Key Function Selection
o2-03 User Parameter Default Value
o2-04 Drive Model Selection
o2-05 Speed Reference Setting Method Selection
Operation Selection when Digital Operator is
o2-06
Disconnected
o3-01 Copy Function Selection
o3-02 Copy Allowed Selection
o4-01 Cumulative Operation Time Setting
o4-02 Cumulative Operation Time Selection
o4-03 Cooling Fan Operation Time Setting
E.3 User Setting Table
User
Setting
507
E