YASKAWA L1000A Technical Manual page 506

E.3 User Setting Table
No.
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
E1-11 Middle Output Frequency 2
E1-12 Middle Output Frequency Voltage 2
E1-13 Base Voltage
E2-01 Motor Rated Current
E2-02 Motor Rated Slip
E2-03 Motor No-Load Current
E2-04 Number of Motor Poles
E2-05 Motor Line-to-Line Resistance
E2-06 Motor Leakage Inductance
E2-07 Motor Iron-Core Saturation Coefficient 1
E2-08 Motor Iron-Core Saturation Coefficient 2
E2-09 Motor Mechanical Loss
E2-10 Motor Iron Loss for Torque Compensation
E2-11 Motor Rated Power
E3-04 Motor 2 Maximum Output Frequency
E3-05 Motor 2 Maximum Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08 Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Frequency
E3-10 Motor 2 Minimum Output Frequency Voltage
E4-01 Motor 2 Rated Current
E4-02 Motor 2 Rated Slip
E4-03 Motor 2 Rated No-Load Current
E4-04 Motor 2 Motor Poles
E4-05 Motor 2 Line-to-Line Resistance
E4-06 Motor 2 Leakage Inductance
E5-02 Motor Rated Power
E5-03 Motor Rated Current
E5-04 Motor Poles
E5-05 Motor Stator Resistance (Single Phase)
E5-06 Motor d-Axis Inductance
E5-07 Motor q-Axis Inductance
E5-09 Motor Induction Voltage Constant 1
E5-11 Encoder Offset
E5-24 Motor Induction Voltage Constant 2
F1-01 Encoder 1 Resolution
F1-02 Operation Selection at PG Open Circuit (PGo)
F1-03 Operation Selection at Overspeed (oS)
F1-04 Operation Selection at Deviation
F1-05 Encoder 1 Rotation Direction Selection
F1-06 PG 1 Pulse Monitor Output Division Ratio
F1-08 Overspeed Detection Level
F1-09 Overspeed Detection Delay Time
F1-10 Excessive Speed Deviation Detection Level
F1-11 Excessive Speed Deviation Detection Delay Time
F1-14 PG Open-Circuit Detection Time
F1-18 dv3 Detection Selection
F1-19 dv4 Detection Selection
F1-20 PG Option Card Disconnect Detection 1
F1-29 dEv Detection Condition Selection
F1-50 Encoder Selection
F1-51 PGoH Detection Level
F1-52 Communication Speed of Serial Encoder Selection
F1-63 PG-E3 R Track Selection
506
User
Name
Setting
No.
F1-66 to
Encoder Adjust 1 to 16
F1-81
F3-01 DI-A3 Option Card Input Selection
F3-03 DI-A3 Option Data Length Selection
F4-01 Terminal V1 Function Selection
F4-02  Terminal V1 Gain
F4-03 Terminal V2 Function Selection
F4-04  Terminal V2 Gain
F4-05  Terminal V1 Bias
F4-06  Terminal V2 Bias
F4-07 Terminal V1 Signal Level Selection
F4-08 Terminal V2 Signal Level Selection
F5-01 Terminal P1-C1 Output Selection
F5-02 Terminal P2-C2 Output Selection
F5-03 Terminal P3-C3 Output Selection
F5-04 Terminal P4-C4 Output Selection
F5-05 Terminal P5-C5 Output Selection
F5-06 Terminal P6-C6 Output Selection
F5-07 Terminal M1-M2 Output Selection
F5-08 Terminal M3-M4 Output Selection
F5-09 DO-A3 Output Mode Selection
F6-01 Operation Selection after Communications Error
F6-02 External Fault from Comm. Option Detection Selection
External Fault from Communication Option Operation
F6-03
Selection
F6-04 bUS Error Detection Time
F6-06 Torque Limit Selection from Comm. Option
F6-08 Reset Communication Parameter
F6-35 CANopen Node ID Selection
F6-36 CANopen Communication Speed
H1-03 Terminal S3 Function Selection
H1-04 Terminal S4 Function Selection
H1-05 Terminal S5 Function Selection
H1-06 Terminal S6 Function Selection
H1-07 Terminal S7 Function Selection
H1-08 Terminal S8 Function Selection
H2-01 Terminals M1-M2 Function Selection
H2-02 Terminals M3-M4 Function Selection
H2-03 Terminal M5-M6 Function Selection
H2-04 Terminal P1-C1 Function Selection (photocoupler)
H2-05 Terminal P2-C2 Function Selection (photocoupler)
H3-01 Terminal A1 Signal Level Selection
H3-02 Terminal A1 Function Selection
H3-03  Terminal A1 Gain Setting
H3-04 
Terminal A1 Bias Setting
H3-09 Terminal A2 Signal Level Selection
H3-10 Terminal A2 Function Selection
H3-11  Terminal A2 Gain Setting
H3-12  Terminal A2 Bias Setting
H3-13 Analog Input Filter Time Constant
H3-16 Offset for Terminal A1
H3-17 Offset for Terminal A2
H4-01 Terminal FM Monitor Selection
H4-02  Terminal FM Gain
H4-03  Terminal FM Bias
H4-04 Terminal AM Monitor Selection
H4-05  Terminal AM Gain
H4-06  Terminal AM Bias
H4-07 Terminal FM Signal Level Selection
H4-08 Terminal AM Signal Level Selection
H5-01 Drive Node Address
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
User
Name
Setting