YASKAWA L1000A Technical Manual page 411

H2-
Function
Setting
5 Speed Detection 2
6 Drive Ready (READY)
7 DC Bus Undervoltage
8 During Baseblock (N.O.)
9 Speed Reference Source
A Up/Down Command Source
B Torque Detection 1
E Fault
F Not used (Through Mode)
10 Minor Fault
11 Fault Reset Command Active
12 Timer Output
13 Speed Agree 2
14 User-set Speed Agree 2
15 Speed Detection 3
16 Speed Detection 4
18 Torque Detection 2
1A During Down Direction
1B During Baseblock 2 (N.C.)
1C Motor 2 Selection
1D During Regeneration
1E Reset Enabled
1F Motor Overload Alarm (oL1)
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
H2 Multi-Function Digital Output Settings
All Modes
Closed: Output speed is greater than or equal to the value in L4-01 with hysteresis determined by L4-02.
All Modes
Closed: Power up is complete and the drive is ready to accept an Up/Down command.
All Modes
Closed: DC bus voltage is below the Uv trip level set in L2-05.
All Modes
Closed: Drive has entered the baseblock state (no output voltage).
All Modes
Open: The speed reference is supplied by an external reference (set in b1-01).
Closed: Digital operator supplies the speed reference.
All Modes
Open: The Up/Down command is supplied by an external reference (set in b1-02).
Closed: Digital operator supplies the Up/Down command.
All Modes
Closed: An overtorque or undertorque situation has been detected.
All Modes
Closed: Fault occurred. (excluding CPF00 and CPF01)
All Modes
Set this value when the terminal is not used or when using the terminal in the pass-through mode.
All Modes
Closed: An alarm has been triggered, or the IGBTs have reached 90% of their expected life span.
All Modes
Closed: The drive has received a reset command from the multi-function input terminals or from serial network, or the
digital operator's RESET key has been pressed.
All Modes
Closed: Timer output.
All Modes
Closed: When drive output frequency equals the speed reference ±L4-04.
All Modes
Closed: When the drive output speed is equal to the value in L4-03 ±L4-04.
All Modes
Closed: When the drive output speed is less than or equal to the value in L4-03 ±L4-04.
All Modes
Closed: When the output speed is greater than or equal to the value in L4-03 ±L4-04.
All Modes
Closed: Overtorque or undertorque has been detected.
All Modes
Closed: Drive is running in the down direction.
All Modes
Open: Drive has entered the baseblock state (no output voltage).
V/f OLV
Open: Motor 1 is selected
Closed: Motor 2 is selected
V/f OLV
Closed: Motor is operated in regenerative mode.
All Modes
Closed: An automatic reset is performed
All Modes
Closed: oL1 is at 90% of its trip point or greater. An oH3 situation also triggers this alarm.
Description
CLV CLV/PM
CLV CLV/PM
B.3 Parameter Table
Page
common_
TMonly 210
common_
TMonly 211
common_
TMonly
211
common_
TMonly 211
common_
TMonly
211
common_
TMonly
211
common_
211
TMonly
common_
TMonly 212
common_
TMonly 212
common_
TMonly 212
common_
TMonly
212
common_
TMonly 212
common_
TMonly 212
common_
TMonly 212
common_
TMonly 213
common_
TMonly 213
common_
TMonly
211
common_
TMonly
214
common_
TMonly 214
common_
TMonly
214
common_
TMonly 215
common_
TMonly
215
common_
TMonly 215
B
411