YASKAWA L1000A Technical Manual page 413

H3: Multi-Function Analog Inputs
■
No.(Addr.) Name
H3-01 Terminal A1 Signal Level
(410H) Selection
H3-02
Terminal A1 Function Selection
(434H)
H3-03
(411H)
Terminal A1 Gain Setting
H3-04
(412H)
Terminal A1 Bias Setting
H3-09 Terminal A2 Signal Level
(417H) Selection
H3-10
Terminal A2 Function Selection
(418H)
H3-11
(419H)
Terminal A2 Gain Setting
H3-12
(41AH)
Terminal A2 Bias Setting
H3-13
Analog Input Filter Time Constant
(41BH)
H3-16
Offset for Terminal A1
(2F0H)
H3-17
Offset for Terminal A2
(2F1H)
Setting Function
Speed Reference Bias
0 (value added to input signal when multiple
analog terminals supply the speed reference)
Auxiliary Speed Reference 1
2
(used as a second speed reference)
Auxiliary Speed Reference 2
3
(used as third speed reference)
E
Motor Temperature (PTC thermistor input)
<44>
14 Torque Compensation (load cell input)
1F Not used (Through Mode)
<44> Available in drive software versions PRG: 7017 or later.
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
Description
All Modes
0: 0 to 10 V
1: -10 to 10 V
All Modes
Sets the function of terminal A1.
All Modes
Sets the level of the input value selected in H3-02 when 10 V is input at terminal A1.
All Modes
Sets the level of the input value selected in H3-02 when 0 V is input at terminal A1.
All Modes
0: 0 to 10 V
1: -10 to 10 V
Note: Use DIP switch S1 to set input terminal A2 for a current or a voltage input signal.
All Modes
Sets the function of terminal A2.
All Modes
Sets the level of the input value selected in H3-10 when 10 V is input at terminal A2.
All Modes
Sets the level of the input value selected in H3-10 when 0 V is input at terminal A2.
All Modes
Sets a primary delay filter time constant for terminals A1 and A2. Used for noise filtering.
All Modes
Applies an offset to analog input A1. Can be used for zero adjustment of the analog input.
All Modes
Applies an offset to analog input A2. Can be used for zero adjustment of the analog input.
H3 Multi-Function Analog Input Settings (H3-02 and H3-10)
All Modes
E1-04 (maximum output frequency)
All Modes
E1-04 (maximum output frequency)
All Modes
E1-04 (maximum output frequency)
All Modes
oH3 Alarm detection level: 1.18 V
oH4 Fault detection level: 2.293 V
V/f OLV
10 V = Motor rated torque
All Modes
Sets this value when the terminal is not used or when using the terminal in the pass-through mode.
Description (For when output is 100%)
CLV CLV/PM
B.3 Parameter Table
Setting Page
common_
Default: 0
TMonly
Min: 0 217
Max: 1
Default: 0
common_
TMonly Min: 0 217
Max: 1F
Default: 100.0%
common_
TMonly Min: -999.9% 218
Max: 999.9%
Default: 0.0%
common_
TMonly
Min: -999.9% 218
Max: 999.9%
common_
TMonly Default: 0
Min: 0 218
Max: 0
Default: 0
common_
TMonly Min: 0 219
Max: 1F
Default: 100.0%
common_
TMonly Min: -999.9% 219
Max: 999.9%
Default: 0.0%
common_
TMonly Min: -999.9% 219
Max: 999.9%
Default: 0.03 s
common_
TMonly Min: 0.00 s 219
Max: 2.00 s
Default: 0
common_
TMonly Min: -500 219
Max: 500
Default: 0
common_
TMonly Min: -500 219
Max: 500
Page
common_
TMonly 220
common_
TMonly 220
common_
TMonly 220
common_
TMonly
220
common_
TMonly
220
common_
TMonly 220
B
413