YASKAWA L1000A Technical Manual page 489

Drive Model
Nominal
CIMR-LU
Output Power
40150
40180 125 - 150
40216
40304
40370
40450
40605 400 - 500
50003
50004
50006
50010
50013
50017
50022
50027
50032
50041
50052
50062
50077
50099
50130
50172
50200
<1> Maximum MCCB Rating is 15 A, or 200% of drive input current rating, whichever is larger. MCCB voltage rating must be 600 Vac or greater.
<2> Maximum Time Delay fuse is 175% of drive input current rating. This covers any Class CC, J or T class fuse.
<3> Maximum Non-time Delay fuse is 300% of drive input current rating. This covers any CC, J or T class fuse.
<4> Class L fuse is also approved for this rating.
Low Voltage Wiring for Control Circuit Terminals
■
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local codes for wiring. If external
power supply used, it shall be UL Listed Class 2 power source only or equivalent. Refer to NEC Article 725 Class 1,
Class 2, and Class 3 Remote-Control, Signaling, and Power Limited Circuits for requirements concerning class 1 circuit
conductors and class 2 power supplies.
Input / Output
Open Collector Outputs
Digital inputs
Analog inputs / outputs
Drive Short Circuit Rating
■
This drive is suitable for use on a circuit capable of delivering not more than 100,000 RMS symmetrical amperes,
600 Vac maximum (Up to 240 V in 200 V class drives, up to 480 V for 400 V class drives), when protected by Bussmann
Type FWH fuses as specified in
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
AC Drive Input Amps
HP
100 142
170
150 207
250 300
300 346
350 410
584
Three-Phase 600 V Class
2 3.6
3 5.1
5 8.3
7.5 12
10 16
15 23
20 31
25 38
30 33
40 44
50 54
60 66
75 80
100 108
125 129
150 158
200 228
Table D.9 Control Circuit Terminal Power Supply
Terminal Signal
P1, C1, P2, C2, DM+, DM-
S1-S8, SN, SC, SP, HC, H1, H2
+V, -V, A1, A2, AC, AM, FM
Table D.1.
L1000A in Heavy Duty Mode (C6-01 = 0)
MCCB Rating Time Delay Fuse
Amps Rating Amps
<1>
225 225
250 250
350 350
500 500
600 600
700 700
1000 1000
<4>
15 6.25
15 8
15 12
20 20
30 25
40 40
60 50
75 60
60 50
75 75
100 90
125 110
150 125
175 175
250 225
300 250
400 350
Requires class 2 power supply
Use the internal LVLC power supply of the drive. Use class 2 for
external power supply.
D.3 UL and CSA Standards
Bussmann
Non-time Delay Fuse Semiconductor Fuse
Rating Amps Rating (Fuse
<2> <3>
Ampere)
400 FWH-400A (400)
500 FWH-500A (500)
600 FWH-600A (600)
800 FWH-800A (800)
1000 FWH-800A (800)
<4>
1200 FWH-1000A (1000)
<4>
1600 FWH-1200A (1200)
<4>
10 FWP-50B (50)
15 FWP-60B (60)
20 FWP-60B (60)
35 FWP-70B (70)
45 FWP-100B (100)
60 FWP-100B (100)
90 FWP-125A (125)
100 FWP-125A (125)
90 FWP-175A (175)
125 FWP-175A (175)
150 FWP-250A (250)
175 FWP-250A (250)
225 FWP-250A (250)
300 FWP-350A (350)
350 FWP-350A (350)
400 FWP-600A (600)
600 FWP-600A (600)
Power Supply Specifications
<4>
D
489